Products

Washer for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

Plastic Drive Rivet - Wheel Arch Trim secures exterior trim panels to the body as part of the wheel arch trim fixing set. This one-piece expanding...

P-Clip for routing and securing engine-bay pipework. Clamps the fuel pipes of the 4-cylinder carburettor petrol engine and the evaporative loss (E...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Bonnet Prop Washer for the Defender bonnet support rod assembly. This washer is fitted to the bonnet prop rod and acts as a bearing/retention surf...

Brake Pipe Clip - a triple retaining clip for the brake hydraulic pipework. It holds three brake pipes together along the chassis run, maintaining...

Steering Lock Bolt for the front axle swivel pin housing, supplied with its nut. Locks the swivel pin housing at the front axle drive shaft. Suppl...

Interior Facia Washer used in the dashboard and facia assembly. The washer distributes the load of a fixing across trim and facia components durin...

Battery Wing Nut secures the battery hold-down clamp within the battery mounting assembly, threading onto the clamp rod to hold the battery firmly ...

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

seal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Sealing Washer - a sealing washer used at cylinder head and thermostat housing joints within the cooling and lubrication circuit. Fitted beneath a...

Interior Trim Fastener - a grey drive-in fastener for securing interior trim panels in the cabin. It retains facia and carpet trim, the cubby box,...

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Caged Nut - a captive plastic nut that receives a self-tapping or trim screw. It clips into a panel aperture to provide a fixed threaded seat, use...

Tilt Stud for the soft top (tilt) and hood frame fixing. Mounts to the body to receive the retaining plate that secures the canopy tilt to the veh...

Spring Plate that retains the soft top (tilt) hood frame. Works with the tilt stud to clamp the canopy in place. Used with stud AFU2503 and ring A...

Blanking Plug for closing a 1-5/8" hole in bodywork or panels. Seals an unused aperture or grommet hole in body panels, brackets and pedal/electri...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Relay

G-Hook - a hook fitting for the soft top drain channel. It anchors and tensions the drain channel that runs along the soft top, holding the channe...

Hazard Warning Switch for the fascia switch panel. Push-push (push-on/push-off) switch that operates the hazard warning flasher circuit.

Courtesy Light Switch is a door-actuated contact switch in the interior lighting circuit, mounted at the door pillar aperture. When the door is op...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Bonnet Striker Pin - the pin the bonnet latch engages to hold the bonnet closed. It mounts to the bonnet and drops into the body-mounted catch, loc...

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Nut Plate for the body-side striker mountings, part of the door and tailboard latch assembly. The plate provides captive threaded anchor points be...

Plate Nut

Nut Plate - captive fixing plate used at the rear body upper mountings. The plate holds the nut captive behind a blind or closed panel section, so...

Nut Plate is a captive threaded plate used in the rear end door latch assembly, providing the fixed threads onto which the tailgate latch mechanism...

Hinge Bonnet - 90/110

Vent Panel Stud Bolt for the dashboard air vent panel assembly on Land Rover Defender without air conditioning. This stud bolt secures the dash ve...

Vent Assembly Knob for the dashboard air vent control on models without air conditioning. The knob fits onto the vent control lever and provides t...

Spire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...

Spire Nut (U-type spire fastener) for trim and panel fixings. Spring-steel push-on nut that clips over a panel edge or stud to provide a captive f...

Clip Nut - a spring clip nut for securing heater and air ducting components. It clips over a panel edge or flange to provide a threaded seat for a...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Spire Nut - a spring U-type nut that slides over a panel edge to receive a self-tapping screw. It provides a captive threaded seat where there is ...