Products

Spire Nut - No. 10 U-Type for use in dashboard and body panel fixings on Land Rover Defender and Discovery I. This U-type spire nut clips onto she...

Spring Nut - Metal U-Clip for body panel and electrical component fixings across a range of Land Rover models. This metal U-clip spire nut clips o...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Spire Nut is a spring-steel sheet-metal fastener that clips over a panel edge or into a pierced hole to provide a threaded anchor point. The arche...

Side Trim Panel is an interior body trim panel that lines and finishes the right-hand side of the 90" wheelbase bodyshell. It conceals the inner bo...

Rear Lower Wheelarch is a body panel forming the lower section of the rear wheelarch on the 110" wheelbase Station Wagon bodyshell. It defines the ...

Rear Lower Body Side Panel - an exterior bodywork panel forming the lower rear section of the side body structure. It provides the outer skin below...

Rear Wheelarch Eyebrow Moulding - Unpainted for the Defender body exterior. This moulding fits over the rear wheelarch aperture, covering the body...

Wheel Arch Moulding – Rear An eyebrow trim moulding fitted to the rear wheel arch lip. It follows the curve of the wheel arch flange, covering the...

Eyebrow Moulding

Rear Wheelarch Moulding is an eyebrow-style trim moulding that fits over the rear wheelarch flange on the outer bodyside, supplied in a gloss finis...

Rear Wheelarch Eyebrow Moulding for the body exterior, supplied in a matt finish. The moulding fits over the rear wheelarch aperture, covering the...

Front Bumper Tapping Plate fitted behind the front bumper mounting points, providing a reinforced steel backing surface for the bumper fixing bolts...

Front Bumper Tapping Block and Bolt Set for securing the front bumper, comprising the tapping block and the associated bolt set. The tapping block...

Front Main Floor Panel for the right-hand side of the cab floor structure. This panel forms the main front floor section on the right-hand side of...

Floor Panel forms the main floor pressing on the left-hand (nearside) side of the body. This pressed-steel panel spot-welds into the body structur...

Door Check Strap Torsion Bar forms part of the side door check-strap mechanism, providing the sprung resistance that holds the door at its intermed...

bar torsion LH

Bar - Torsion

Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...

Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...

Spare Wheel Carrier mounts to the rear door to carry the spare wheel externally. It bolts through the door and provides the stud plate onto which ...

Window Regulator for the front door, left-hand side. The regulator is the mechanism inside the door that raises and lowers the door glass, carrying...

Window Regulator - Right-Hand for the Defender 90/110 door glass assembly. This regulator operates the right-hand side door window, converting the...

Door Glass for the front door, left-hand side, in clear (un-tinted) glass. This is the sliding window pane that runs in the door channels and is ra...

Door Glass for the front door, left-hand side, in light green tinted glass. This is the main glass panel for the front door, forming part of the d...

Door Glass for the front door, right-hand side, in clear glass. This is the main glass panel for the front door, forming part of the door glazing ...

Body Seal seals the joint at the lower edge of the rear upper body section on Hard Top models. The single seal serves both the left- and right-han...

Body Seal seals the joint between the rear upper body panel and the lower body section.

Rear Upper Waist Seal. It seals along the upper waist line of the rear body, closing the joint between the body side and the glass line to keep out...

Truck Cab Waist Seal for the Land Rover Defender truck cab body variant. This rubber seal fits at the waist level of the truck cab body, sealing t...

Seatbase Storage Lid closes the storage locker built into the seat base. This lid fits over the stowage compartment within the seat base, providin...

Window Regulator Handle Adaptor for the front door glass and window regulator assembly. The adaptor couples the manual window winder handle to the...

Front Door Outer Waist Seal fitted along the upper edge of the front door outer panel, sealing the interface between the outer panel and the door d...

Front Door Outer Waist Seal fitted along the upper edge of the front door outer panel, sealing the interface between the outer panel and the door d...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Front Outer Wing - Aluminium - LH for the Defender outer body panel assembly. This left-hand front outer wing is manufactured in aluminium and doe...

Front Outer Wing for the right-hand side, in the no-vent configuration without the side vent aperture. This outer wing panel forms the front bodyw...

Tailgate Seal, rubber weatherseal for the rear tailgate. It fits around the tailboard aperture, sealing the joint between the closed tailgate and ...

Front door latch link

Bonnet stay stick Defender

Front Door Sill Seal fits along the lower door aperture as part of the body sealing system, sealing the threshold at the base of the front door ope...

Door Sill Seal - rear, supplied as a left- and right-hand pair. This rubber seal fits along the rear door sill aperture, forming the weather seal b...

Pop Rivet - a blind (pop) rivet for fastening panels, trim and seals where access is available from one side only. The rivet is set with a hand or ...