Products

Fixing Screw for the front door hinge and check strap assembly. This screw secures the door hinge and the check strap (door-stay) to the body pill...

Restore and protect your Land Rover Defender 90/110 with this Genuine Right-Hand Front Wheel Arch Liner. Designed as a direct replacement, this dur...

Front Wheel Arch Assembly - a galvanised body section forming the front wheelarch and eyebrow. The assembly mounts to the front bodywork to enclos...

Relay is a 12V 60A change-over relay used in the vehicle electrical system to switch a high-current circuit through a low-current control signal. ...

Bonnet Stay Bracket - mounting bracket for the bonnet stay. Locates and supports the bonnet stay, holding the bonnet in the open position for engi...

Bonnet Stay Bracket is the left-hand mounting bracket for the bonnet stay. It forms the pivot-bush end of the bonnet stay assembly, providing the ...

Sill Panel Stay is a support bracket for the sill (rocker) panel. Forming part of the sill panel assembly, it braces the sill panel to the body st...

Front Fender Panel - RH is the right-hand front wing panel, the outer body panel covering the front wheel arch and forming the side of the front bo...

Front Panel - TD5 - LH

Idle Adjusting Needle is the mixture-adjusting needle for the Zenith Stromberg CD175 constant-depression carburettor fitted to the Rover 3.5 V8. I...

Inner Wheel Arch Panel - RH is the right-hand front inner wheelarch (wheel housing) panel, the galvanised body section forming the inner wall of th...

Tailgate Trim is the rear end door casing, an interior trim panel fitted to the inner face of the rear end door. It provides a finished interior s...

Air Intake Finisher is the wing-top grille that covers the cold air intake aperture of the induction system. This is the right-hand wing-top finis...

Air Intake Grille is the louvred wing-top panel that covers the cold-air inlet at the base of the windscreen. Mounted on the left-hand wing top, i...

Air Intake Blanking Plate closes off the right-hand wing-top air-intake aperture where a cold-air inlet is not required. It fits the same opening ...

Air Intake Blanking Plate closes off a wing-top air intake aperture in the induction system. This is the left-hand wing-top blank for left-hand-dr...

Radio Cassette Housing for the Defender 90/110 dashboard interior trim assembly. This moulded trim housing surrounds and retains the radio cassett...

Fastener is a fixing used to secure exterior body trim and finisher panels to the bodywork. It retains trim components such as plinths and finishe...

Sunroof Finisher is a trim finisher for the sunroof assembly. It frames the edge of the sunroof aperture, concealing the join between the sunroof ...

Bonnet Insulation Pad for the engine bay sound-and-heat insulation system. Fits to the underside of the bonnet, where it dampens engine noise tran...

High-Mounted Stop Lamp Stud is a mounting stud for the high-level stop lamp. It secures the high-level (centre) stop lamp to its mounting point on...

High-Mounted Stop Lamp Stud is a mounting stud for the high-level stop lamp. It secures the high-level (centre) stop lamp to its mounting point on...

Special Nut is an M8 blind nutsert, a threaded insert set into a panel to create a captive fixing point. Installed from one side of the panel, it ...

Seat Squab is the backrest section of the right-hand front seat assembly. The squab forms the upright cushion against which the occupant's back re...

Seat Base Cushion - Front for the front seat assembly. This cushion forms the lower seating surface and mounts onto the front seat frame, supporti...

Seat Cushion Cover for the front seat, forming the outer covering over the seat base cushion - the part of the seat you sit on. It replaces a worn,...

Seat Squab Cover for the front seat backrest (squab), forming the outer covering over the backrest cushion. It replaces a worn, torn or faded origi...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Facia Finisher (RHD) - the trim finisher strip that runs along the top of the dashboard facia, from the instrument binnacle across to the passenger...

Facia Finisher (RHD) - the trim finisher strip that runs along the top of the dashboard facia, from the instrument binnacle across to the passenger...

Heater Hose - Inlet for the engine coolant and cabin heater circuit on the Td5 2.5L 5-cylinder turbo diesel. Carries hot coolant from the engine f...

Heater Hose is a coolant hose in the heater circuit of the Td5 2.5L 5-cylinder turbo diesel. It carries engine coolant between the cooling system ...

Heater Outlet Hose is the coolant return hose from the heater matrix on the 4.0L V8 EFI petrol. It returns coolant from the heater matrix to the e...

Blind Nutsert is an M6 blind rivet nut (rivnut) that provides a captive threaded fixing point. It is set into a single face of sheet metal or pane...

Bonnet Grommet is a rubber grommet fitted within the bonnet assembly. It lines the aperture through which the bonnet prop rod or release mechanism...

Plain Washer M8

Special Fixing Washer for the hardtop side-frame mounting. Seats over the M8 side-frame mounting stud and under its securing nut, spreading the cl...

Washer for the non-hinged windscreen frame assembly. It seats on the frame fixings, spreading the fastener clamp load across the mounting surface ...

Flanged Bolt - M8 x 25 mm, Torx drive. Secures the lower body-to-chassis mounting points at the rear of the vehicle. The integral flange spreads c...

Bulkhead Mounting Bolt - M12 x 180mm fastener securing the lower bulkhead to the chassis. Forms part of the body-to-chassis mounting at the base o...

Domed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...