Products

Steel Ball - 9/32 inch steel ball used in the steering column assembly. Supplied individually. Ball diameter 9/32 inch (7.14 mm).

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Body Aperture Harness Grommet for the wiring harness routing assembly. Rubber grommet installed in a body panel aperture to seal and protect wirin...

Brake Pipe Connector - a junction fitting in the hydraulic brake circuit that joins rigid brake pipes. It provides a sealed connection between bra...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Window Regulator Clip is a retaining clip within the side door window regulator assembly. It secures the link between the winder mechanism and the...

Clip

Jack Rack. A mounting rack that stows and secures a jack to the vehicle, holding it firmly in place for transport.

LED Light Kit - 73mm

Shock Absorber - front gas-charged suspension damper. Mounted between the front axle and the chassis, it damps spring oscillation to control body ...

Front Shock Absorber Bush Kit for the front suspension assembly. Bush kit for the front shock absorber mounting, providing the rubber isolation be...

Shock absorber rear Pro-Comp gas 0-25 mm (+1")

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Outer Wing is the left-hand front wing outer skin panel, moulded in ABS plastic. It forms the visible outer surface of the front wing, covering th...

Bush Kit Pro-Comp Only BR 2255PK

Inner Pinion Bearing for the Salisbury rear axle. This taper-roller bearing supports the inner end of the differential pinion shaft, carrying the ...

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

Decoke Gasket Set for the Td5 diesel engine, late specification. This is the upper-engine gasket and seal set used when decarbonising the engine or...

Decoke Gasket Set - the set of gaskets required for a top-end decarbonising (decoke) and cylinder head removal, supplied without the cylinder head ...

Rivet used within the main wiring harness assembly to secure harness routing and retain protective coverings to body mounting points. Maintains st...

Camber Bush Set for the front radius arms, 38mm wide. The bushes locate in the front radius arm mountings and set the caster and camber geometry o...

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Radiator with Integrated Oil Cooler - the main engine cooling radiator for the 200 TDi diesel engine, incorporating a built-in engine oil cooler an...

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Radiator is the main engine cooling radiator with an aluminium core, serving the front of the engine cooling circuit. Mounted ahead of the engine ...

Decal - TDi - a self-adhesive "TDi" engine decal for the front wing, in light grey and measuring 9cm. The decal reproduces the original "TDi" wing...

Decal

Decal

Front Grille Badge is the model identification badge fitted to the front grille panel. It mounts to the grille to carry the marque branding at the...

Land Rover Logo Tape - adhesive decal, 25cm length. Self-adhesive Land Rover logo tape from the Defender transfers and graphics range. Applied to ...

Body Decal reading 'Defender 110' - an exterior self-adhesive graphic finished in silver lettering on a clear backing. The decal is applied to the...

Heater Hose forming part of the cabin heater coolant circuit, carrying return coolant from the heater matrix back to the engine cooling system. Fo...

Heater Hose for the 200 TDi engine's heating circuit. It carries engine coolant between the cooling system and the heater matrix, forming part of t...

Heater Hose forming part of the cabin heater coolant circuit, carrying feed coolant from the engine cooling system to the heater matrix. For the 2...