Products

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Joint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...

Valve Cup for the valve gear of the 3-bearing 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The cup seats on the top ...

Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Gerschikt voor 2.25 ltr benzine

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Distance piece

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Retainer

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Pedal Shaft is the transverse shaft on which both the clutch pedal and brake pedal are mounted within the cab, on vehicles without a brake servo. ...

Top cover

Pedal Pivot Bush is the bearing bush on which the clutch or brake pedal pivots within the pedal box assembly. Pressed into the pedal bore, it prov...

Clutch Pedal Box Top Gasket for the clutch pedal housing on manual transmission vehicles. This gasket seals the joint between the clutch pedal box...

Leaf Spring Heavy Duty

Rear Leaf Spring - heavy-duty rear leaf spring for the passenger side, built with eight leaves for increased load capacity. Locates the rear axle ...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Banjo bolt

Manifold Gasket for the 2.25L and 2.5L 4-cylinder petrol engines. This gasket seals the combined inlet and exhaust manifold assembly to the cylind...

Handbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...

Rocker Cover Gasket for the 2.6L six-cylinder petrol engine, sealing the side rocker cover to the cylinder head. It forms the oil-tight joint alon...

Timing Chain Vibration Damper for the front timing chain drive on four- and six-cylinder engines. Mounted within the timing cover, it bears agains...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Oil Feed Pipe is the external oil feed pipe supplying the cylinder head within the engine lubrication system. It carries pressurised oil from the ...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Inlet Air Seal for the Solex carburettor connection on the 2.25L 4-cylinder petrol induction system. Seals the joint between the air intake and th...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Past op  1958 - 61:   Sommige S 3 vanaf 1977 en 110 1983 - 84 All 3 Lug Internal Fixings

Timing Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...

Intermediate Shaft

Carburettor Spacer for the petrol engine induction system, fitting between the carburettor and the inlet manifold. It sets the carburettor off the...

Carburettor Manifold Gasket for the 2.25L petrol and carburettor-equipped Defender engines. This gasket seals at the interface between the carbure...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Cylinder Head Bolt is the short-length head bolt that clamps the cylinder head to the block on the 2.25L and 2.5L 4-cylinder petrol engines. The h...

Bowl Washer is the sealing joint washer for the fuel sediment bowl (sedimentor) in the fuel system. It seals the bowl to its housing, maintaining ...

Nut with a 5/16 inch BSF (British Standard Fine) thread. A hexagonal fastener that threads onto a matching 5/16 inch BSF bolt or stud to secure a ...