Products

Cab Mounting Stud

Door Hinge Bolt

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Door Hinge Spring for the rear door hinge assembly. Return spring fitted within the rear end door hinge on station wagon body variants. Provides t...

Locker Door Hinge

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Floor Mat Retainer secures the intermediate second-row rubber floor mat. Holds the mat in position against movement underfoot.

Floor Mat for the second seat row, a ribbed rubber mat protecting the intermediate floor area. Approximate dimensions 1490 x 460 x 3 mm.

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Seat Squab Bolt - shouldered bolt for mounting the seat squab (backrest) to its frame. This shouldered bolt secures the seat squab at its mounting...

Leather hasp civilian

Tailgate Buffer - rubber buffer for the rear tailgate (tailboard). This rubber buffer cushions the tailgate where it meets the body, absorbing the...

Female Dovetail for the rear end door latch mechanism. Receives the male dovetail to align and secure the rear door as it closes. Sold individually.

Pillar seal

Window Seal: rubber glazing seal for the window glass, sealing it against water and draughts.

Sliding Window Catch secures the sliding glass of the front door side window, locking the two panes together so the window can be held shut or fixe...

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Fitment: all models to 1980

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Glass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.

Aluminium Corner Strip - the curved top retainer for the rear door glass. One of the aluminium retainers in the rear (end) door glazing set, this ...

Check rod RH

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...

Rear Body Seal is a rubber seal fitted to the rear body extension panel of the station wagon body. The seal closes the gap between the extension p...

Mounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...

Rubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...

Bodyside Seal for the lower edge of the rear upper body section, sealing the joint between the upper body structure and the lower body on the rear ...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Roof Panel Seal - Right-Hand for the Defender 110 rear upper body, sealing the joint between the right-hand roof panel edge and the upper body stru...

Roof Panel Seal - Left-Hand for the Defender 110 rear upper body, sealing the joint between the left-hand roof panel edge and the upper body struct...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Circlip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...

Cab Body Panel Mounting Bracket - a body bracket that locates and secures a cab panel to the surrounding body structure. It provides the fixing po...

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...