Products

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Side Panel Buffer, a rubber buffer fitted at the rear body side panels. Sits between the upper and lower rear quarter panels, cushioning the joint...

Mounting stud

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Seat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Grommet - Blanking Plug, Gearbox Tunnel for Land Rover Series II and III. This small rubber blanking plug fits into an aperture in the top of the ...

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Door lock RH

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Spare Wheel Bonnet Strap, the retaining strap for a bonnet-mounted spare wheel. Secures the spare wheel in the bonnet-top carrying position, holdi...

Number Plate Lamp Plinth is the mounting base for the rear number plate lamp, fixing the lamp unit to the bodywork above the number plate. It loca...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Rope Hook

Hook

Headlamp Guard in galvanised steel. A protective grille fitted over the headlamp lens to shield it from stone chips, debris and impact damage. The...

Headlamp Guard in moulded plastic. A protective guard fitted over the headlamp lens to shield it from stone chips, debris and impact damage. Suppl...

Air Vent Mechanism - operating mechanism for the dash-mounted fresh-air ventilator. Controls the opening and closing of the bulkhead air vent flap...

Dashboard Assembly Plate is a structural panel within the facia assembly, forming the mounting base onto which the instrument panel and dashboard t...

Instrument Cover is the trim cover for the instrument pack within the facia assembly, enclosing the main gauge cluster. It is also used as the cov...

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Door Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...

Heater Control Mounting Plate for the heater control assembly. It provides the fixed mounting that carries the heater control unit, locating the co...

Heater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...

Hose Clip Spring is the spring connector clip for the heater demister and air outlet pipes. Retains the demister ducting and outlet flaps within t...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...

Sill Panel Rear 109 Not Station Wagon - LH

Door Hinge Shim for the Land Rover door hinge assembly. This 1mm shim is fitted between the door hinge and its mounting face to set or adjust the ...

Bracket

Replace or upgrade the front outer wing panel on your Series 2/3 Land Rover with this aluminium panel designed for Right-Hand Side (RHS) and Left-H...

Front outer wing RH SIII plastic

Heater Control Mounting Plate for left-hand drive applications. Fitted within the heater control assembly in the cab interior, this plate provides ...