Products

Shim door GENUINE - door striker plate 1958 - 1984 - side hinged tailgate

Grille Spring Clip for securing the front grille panel on Series III models. Fitted at the grille mounting points, this spring clip retains the fro...

Heater Cable operates the tap-type heater control valve in the heating and ventilation system. It connects the dashboard heater control to the tap...

Radiator Panel for the front-end assembly on Series III models. This panel forms the surround and support structure for the radiator, integrating w...

Window Channel

Window Channel

Window Channel - Top is the upper glass-run channel that guides the top edge of the window glass, supplied as a 94 cm length. It forms the running...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Seat Base Corner Capping in plastic. Fitted at the outer corners of the front seat base frame, this capping provides a neat finished edge and prote...

Seat Frame for the adjustable driver's seat on Series II and Series III models. This structural frame forms the base of the driver's seat assembly.

Bush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"

Bush

Interior Mirror Plate is the base/fixing plate that mounts the interior rear-view mirror to the body. It is a three-hole mounting plate that faste...

Steel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.

Steel Ball, a precision steel ball used within the engine oil pump assembly of the lubrication system. It seats inside the oil pump body as a comp...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Wiper Motor Shaft & Gear is the internal drive shaft and gear for the central windscreen wiper motor, providing a 120-degree sweep. It transmi...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Bonnet Buffer for the Land Rover bonnet assembly. This rubber buffer mounts to the body structure and provides a cushioned contact point for the u...

Fuel Tank Mounting Washer is used at the fuel tank mounting points, spreading the clamping load of the fixing across the mounting bracket or strap....

Door Latch Shim - Rear - a packing shim for the rear door anti-burst latch, part of the door lock and handle assembly. Fitted behind the latch on ...

Barrel Lock with Key A lock barrel (cylinder) supplied complete with its key, forming the keyed locking element of the door lock assembly. The bar...

Front Door Lock Set provides key-operated locking for the front doors and is of the anti-burst type, designed to resist the latch springing open un...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Front Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...

Door Seal for the front door, part of the door sealing system. Runs around the front door aperture to seal the gap between the door and the body s...

Door Seal for the front door, part of the door sealing system. Runs around the front door aperture to seal the gap between the door and the body s...

Door Seal - Front - Top is the weatherstrip that closes the joint between the top edge of the front door and the roof cant rail, forming part of th...

Door Seal - Front - Top is the weatherstrip that closes the joint between the top edge of the front door and the roof cant rail, forming part of th...

Heater Duct, right-hand side, within the heater demister and air distribution system. Channels air from the heater assembly to the windscreen demi...

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Upper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...

Door Check Strap Assembly A check strap that limits how far the side-hinged tailgate opens and holds it at its open position. Fitted to the lower ...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Plain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.

Split Pin for use in the front and rear suspension assembly of the Series Land Rover. The split pin is inserted through the hole in a castle nut o...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...

Clip