Products

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Track spacer oil seal

Baulk Ring (Synchroniser Ring) for the LT77 five-speed manual gearbox. Fits the mainshaft synchromesh hubs to match shaft speeds during gear engag...

Reverse Idler Gear Assembly for the LT77 five-speed manual gearbox. Provides the reverse gear train, reversing mainshaft rotation for reverse driv...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Front Propeller Shaft connecting the transfer box front output to the front axle differential. It transmits drive from the transfer box to the fro...

Rear Propeller Shaft assembly for the rear axle driveline. Installed between the transfer gearbox rear output flange and the rear differential inp...

Front Propshaft for 4-cylinder applications, forming part of the drivetrain. It transmits drive from the transfer box front output flange to the fr...

Front Propshaft for 4-cylinder applications, forming part of the drivetrain. It transmits drive from the transfer box front output flange to the fr...

5th Gear Bias Spring is the gearchange bias spring within the LT77 gearbox shift mechanism. It applies spring load to the selector to bias the gea...

Gearchange Ball Pin Gasket seals the gearchange ball pin housing to its mounting face on the gearbox. The ball pin housing carries the pivot for t...

Plain Washer is a flat load-spreading washer used in the front axle hub and drive shaft assembly. It sits beneath the retaining fastener to distri...

Clevis Pin used to secure a clevis or yoke joint in a mechanical linkage. The pin passes through the yoke and mating rod end and is retained by a ...

Clip

Pin - Split

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Gear Lever Knob for the LT77 5-speed manual gearbox. Fits the main gear lever of LT77-equipped vehicles, including V8 petrol manual variants. The ...

Transfer Box Clevis Pin for the LT230 transfer box gear change linkage. This clevis pin connects the high/low gear change lever to the transfer bo...

Clevis pin

Clevis pin

Clip

Mainshaft Gear for the LT230 transfer gearbox, carrying 26 teeth. The gear is mounted on the transfer box mainshaft and forms part of the gear tra...

Gear Lever Bias Plate for the manual gearbox gear change mechanism. It sits in the gear lever remote housing and works with the bias spring to load...

Synchro Assembly for fifth gear in the LT77 five-speed manual gearbox. The synchroniser matches the rotational speed of the gear to the shaft befo...

Gearbox Breather for the gearbox and transfer case assembly. This breather is located on the gearbox or transfer case casing and vents internal pr...

Breather Tube for the LT230 transfer box. This tube forms part of the breather system on the LT230 transfer gearbox, routing pressure venting away...

Gearchange Lever - Lower forms the lower section of the manual gearbox remote gearchange linkage. It connects the upper gearchange lever to the ge...

Synchromesh Assembly - 3rd & 4th is the synchroniser unit for 3rd and 4th gears in the LT77 5-speed manual gearbox. Mounted on the mainshaft b...

Circlip - LT77 Mainshaft is a retaining circlip used on the mainshaft of the LT77 5-speed manual gearbox. It seats in a groove on the mainshaft to...

Thrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...