Products

Exhaust Front Pipe is the first section of the exhaust system, connecting the exhaust manifold to the downstream pipework and silencer. It carries...

Banjo Bolt for diesel fuel pipe connections at the fuel filter. This hollow bolt secures a banjo union to its port, allowing fuel to pass through ...

O-Ring sealing the air filter housing to the airflow meter on V8 EFI engines. This O-ring seals the joint between the air filter housing outlet an...

Clutch Hose for the hydraulic clutch actuation system. This flexible hose provides the hydraulic connection between the rigid clutch pipework and t...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Coolant Adaptor (Reducer) - threaded adaptor in the engine oil cooler circuit at the radiator. This threaded reducer adaptor connects the engine o...

Exhaust pipe V8 EFI

Power Steering Hose - part of the power steering hydraulic circuit. This hose carries pressurised hydraulic fluid within the power steering system...

Radiator Top Hose for the 200TDi 2.5L turbo diesel cooling circuit. Connects the engine outlet at the thermostat housing to the top inlet of the r...

Oil Cooler Pipe for the engine oil cooling circuit on diesel engines, running between the oil cooler and the pump feed. Carries engine oil under p...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Brake Master Cylinder for the brake hydraulic circuit, converting brake-pedal force into hydraulic pressure supplied to the front and rear brake li...

Front Bumper for the Discovery 1, fitting the pre-facelift body specification across petrol and diesel engine variants. This steel bumper mounts t...

Front bumper end cap, right-hand side, from the front bumper assembly. The end cap closes off the outboard end of the front bumper where the bumpe...

Front Bumper End Cap - Left Hand is the moulded outer closure panel of the front bumper assembly. It fits over the outboard end of the front bumpe...

Rear Bumper End Cap for the left-hand (LH) outboard end of the rear bumper assembly, finished in black. The end cap closes off the open end of the...

Rear Bumper Reflector for the Discovery 1, fitting the designated aperture in the rear bumper to meet lighting regulations. The red retro-reflecti...

Retaining Clip used in the parking brake (handbrake) assembly and the automatic transmission gear-change linkage. The clip secures a pivot pin or ...

Exhaust Mounting Rubber - flexible support that suspends the silencer section of the exhaust system from the vehicle underbody. The moulded rubber...

Bottom Radiator Hose for the engine cooling circuit on the V8 Petrol engine. Connects the lower outlet of the radiator to the coolant pump inlet o...

Exhaust Bracket for the exhaust system mounting. The bracket supports and locates a section of the exhaust line against the underbody, typically w...

Fuel Tank Cradle - the support cradle that carries the fuel tank beneath the vehicle, bolting to the chassis to hold and locate the tank. Heavy-du...

Oil Cooler Hose for the engine oil cooling circuit on the V8 engine. Forms part of the hose assembly linking the engine oil cooler to the oil circ...

Fuel Tank Lock Ring secures the in-tank fuel pump and sender assembly to the top of the fuel tank. The ring locks down over the tank aperture, hold...

Fuel Pump Seal for the fuel tank sender unit. This seal seats at the mounting flange of the fuel pump and sender unit where it interfaces with the ...

Sealing Grommet seals the aperture in the fuel tank top face around the fuel pump or tank sender unit. It sits between the pump or sender flange a...

PAS Hose – Reservoir to Pump for the power-assisted steering hydraulic circuit. This low-pressure feed hose carries fluid from the steering reservo...

Power Steering Hose - the high-pressure feed line in the power steering hydraulic circuit. It carries pressurised fluid from the power steering pu...

Spring Retaining Plate in the rear suspension, securing the upper end of the rear coil spring. It locates and clamps the top of the coil spring ag...

Handbrake Cable transmits lever movement to the transmission handbrake, the drum brake mounted on the transfer box rear output. The outer sheath i...

Oil Cooler for the V8 Petrol engine oil cooling system. Reduces engine oil temperature by routing oil through a dedicated cooler core, maintaining...

Exhaust Pipe – Intermediate for the exhaust system. The intermediate pipe links the front downpipe to the rear silencer section, routing exhaust ga...

Anti-Roll Bar Strap Bracket for the front suspension assembly. Provides the mounting point for the anti-roll bar strap on the axle casing. The bra...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Radius Arm Bush - Front - mounts the front radius arm at its axle end within the front suspension. The radius arm locates the front axle longitudi...

Radius Arm Bush Set - Front - a set of polyurethane bushes for the front radius arm axle-end mountings. The radius arm locates the front axle long...

Hose pump to box

Exhaust Silencer for the 200Tdi 2.5L Turbodiesel exhaust system, non-catalyst specification. Fits in the mid-to-rear section of the exhaust system...

Anti-roll bar bush