Products

Piston for the 3.5L Rover V8 petrol engine, supplied at +0.020" oversize with an 8.13:1 compression ratio. The +0.020" oversize suits a rebored bl...

Locking Wheel Nut Kit - Spare Wheel

Clutch Plate

Clutch Plate

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Clutch Kit 3.9V8 AP

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Camshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Camshaft Bearing for the 2nd, 3rd and 4th journal positions of the four-cylinder engine. The bearing shell is fitted into its housing in the cylind...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Exhaust Clamp for the V8 engine exhaust system, securing a front-pipe joint. The clamp draws two pipe sections together at their slip joint, holdin...

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Pedal Box Pivot Bolt for the pedal box assembly, forming the pivot axis on which the brake or clutch pedal swings within its mounting bracket. The...

Locking Washer for the swivel pin housing on the front axle. The washer sits under the swivel pin retaining bolts, and its tab is bent up against t...

Trunnion

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Oil Pump Relief Plunger is the pressure-relief valve plunger within the engine oil pump, part of the lubrication system on the 3.5L V8 petrol engin...

Gasket is a sealing gasket used in the V8 petrol engine assembly. It forms a seal between two mating components, preventing leakage of fluid or gas...

Dowel used for the precise location and alignment of the front cover to the cylinder block on Rover V8 engines. These dowels ensure the front cove...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Speedo drive oil seal LT230

Cable Tie, a push-fit strap for routing and securing wiring and hoses. The tie strap bundles and secures wiring looms, pipes and hoses, locating i...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Sedimentor Seal for the diesel fuel sedimentor assembly. The sedimentor separates water and sediment from the fuel ahead of the injection system. ...

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Self-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...

Screw for use in Land Rover body, chassis, and hardware applications.

Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Self-Tapping Screw for interior trim fixing, used to secure the sunroof roller blind assembly. The self-tapping thread forms its own mating thread...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Self Tapping Screw for use in Land Rover body, chassis, and hardware applications.

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Screw is a threaded fastener used to secure components during assembly.

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Screw for body and interior trim fixing. Used to secure body panels and interior trim components. A threaded fastener for general body and trim as...

Tap screw

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

Screen Washer Pump for the rear window wash circuit. This electric pump draws washer fluid from the reservoir and delivers it under pressure to th...

Brake pipe clip

Sensor

Transmitter - Sensor