Products

24v dsl long belt

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Locking Nut for Land Rover applications.

Suspension Damper

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

LED Festoon Bulb for interior lamps. A double-ended festoon LED that replaces the standard filament festoon bulb in the courtesy, map and interior...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Gearbox Oil 75W80 is a 75W80-grade manual transmission fluid (MTF) formulated for the R380 5-speed manual gearbox. It lubricates the gears, synchr...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Hex Nut is an M8 copper flanged-head nut used on the exhaust manifold. The flanged head spreads the clamping load and removes the need for a separ...

Front Brake Hose - flexible hose in the front hydraulic brake circuit, connecting the rigid brake pipe on the body to the front brake caliper. Rei...

Camshaft Position Sensor monitors the rotational position of the camshaft and reports it to the engine ECU. The ECU uses this signal to identify c...

Depression Control Valve mounted on the camshaft cover of the diesel engine. It regulates the internal depression (vacuum) of the engine, maintain...

Water Pump Gasket

Fuel Spill Return Pipe - part of the fuel injection system, connecting the injector leak-off ports to the fuel return line. It collects spill (lea...

EGR Valve Control - vacuum control valve in the exhaust gas recirculation (EGR) system. Regulates the vacuum signal that operates the EGR valve, c...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Screw for use in Land Rover body, chassis, and hardware applications.

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Body Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Insulation Pad Clip A fir-tree style retaining clip that holds the under-bonnet sound-deadening and heat insulation pad in place. The clip pushes ...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Rear Door Latch Assembly - the latching and locking mechanism for the rear door. It engages the striker on the body aperture to hold the rear door...

Bonnet Release Cable for the bonnet latch assembly on the Freelander 1. This cable runs from the interior release handle, through the bulkhead and...

Window Regulator for the rear door, right-hand side, manual winder type (not electric). This is the mechanism that raises and lowers the rear door...

Locking Fuel Filler Cap Assembly. It seals the fuel filler neck and locks to secure the filler against unauthorised access. Supplied to a non-speci...

Latch Actuator the central locking actuator for the rear end door latch. The electric actuator drives the rear end door latch between its locked a...

Front Door Lock (Latch) Assembly for the left-hand door on left-hand-drive applications, part of the door body fittings and central-locking system....