Products

Brake Pad Set - Rear - friction pad set for the rear axle of the service brake system. The pads locate in the rear brake calipers and are clamped ...

Brake Disc - Rear - brake disc for the rear axle, supplied as a pair. The disc mounts to the rear hub and provides the friction surface that the r...

Brake Disc - Front Vented - internally ventilated brake disc for the front axle, supplied as a pair. The disc mounts to the front hub and provides...

Rear Brake Discs for the rear disc brake assembly. Petrol applications. Each disc mounts to the rear hub and provides the friction surface against...

Front Brake Discs for the front disc brake assembly. Petrol applications. Each disc mounts to the front hub and provides the friction surface agai...

Rear brake discs, supplied as a matched pair for the rear axle. The disc provides the friction surface of the rear braking assembly: it is mounted...

Turbo Hose for the 2.2 TD4 diesel forced-induction system. It carries pressurised charge air within the turbocharger boost circuit and is pre-forme...

Upgrade your Land Rover Freelander 2 (2.2 TD4 Diesel) with this high-performance Silicone Turbo Hose Kit, designed to handle higher temperatures an...

Rubber Mats - Front & Rear - LHD - FL2

Brake Pad - Front is a set of disc brake friction pads for the front axle. The pads are clamped against the brake disc by the caliper to generate ...

Brake Pad Set - front axle, part of the front disc brake assembly. The pads sit in the caliper carrier and are pressed against the brake disc by t...

Coupling Filter for the Gen 3 Haldex rear drive coupling. The Haldex coupling is an electronically controlled multi-plate clutch unit mounted ahea...

Freelander2 Gen3 Coupling Filter

Clutch Kit for the 2.2L TD4 diesel driveline, supplying the friction and release components required for a complete clutch replacement. The kit co...

Fog light cover set - a pair of chrome-finished plastic surrounds that fit over the front bumper fog lamp apertures. The covers locate around the ...

Rear Differential Pinion Bearing Kit for rebuilding the pinion bearing assembly in the rear differential. The kit contains the pinion bearings and ...

Front Differential Bearing Overhaul Kit - an overhaul set for the Power Transfer Unit, the front drive unit that bolts to the transverse gearbox, c...

FL2 Rear Diff Pinion Bearing Kit No Oil

Diff Overhaul Kit - No Oil - Rear

Rear Differential Overhaul Kit - a pinion bearing overhaul set for the rear final drive unit, covering the bearings that locate the pinion shaft wh...

Seat Back Adjustment Handle - the operating handle for the front seat backrest recline mechanism, mounted on the outboard side of the seat frame. ...

Towing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...

Bolt - M10 x 25 mm, with washer. Underbody and chassis fixing used to secure engine splash shields, heat shields and underbody protection panels t...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Cylinder Head Bolt - KV6 2.5L Petrol

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Breather filter (M47 2.0L I4 16V Diesel) (M57 D30 3.0 Diesel)

Hex Nut - M12 x 1.25 - fine-thread fastener used at the top mounting of the front suspension strut. It secures the strut rod at the upper mounting...

Servo Seal - rubber grommet fitted to the brake vacuum booster (servo) housing. It seals the connection into the booster body, maintaining the vac...

Cap - Expansion Tank

Radiator Cap - screw-on pressure cap for the coolant expansion tank in the engine cooling system. The cap seals the expansion tank and holds the c...

Pedal Switch - multi-function pedal-position switch used in the brake and clutch pedal controls on manual transmission vehicles. The switch is mou...

Bolt and Washer Assembly - hex-head bolt with captive washer, used in the front suspension and cross member mountings. It secures the front cross ...

Hex-Head Bolt and Washer - bolt and washer assembly used in the front suspension and subframe area. The fastener secures front cross member, stabi...

Oil Pan Plug for the oil level indicator aperture, fitted to the sump of the 3.2L DOHC MPI I6 petrol engine. The plug closes and seals the oil lev...

Sump Plug Washer for the 3.2L DOHC MPI petrol inline-six engine. This sealing washer fits under the sump drain plug to seal the oil pan drain threa...

Sump Plug Washer for the 3.2L DOHC MPI petrol inline-six engine. This sealing washer fits under the sump drain plug to seal the oil pan drain threa...

Anti-Roll Bar Bush for the suspension stabiliser system. This rubber insulator clamps the anti-roll bar to its mounting, locating the bar while all...

Brake Calliper Carrier - Front - the fixed bracket that mounts the front brake calliper to the hub carrier. The carrier bolts to the steering knuc...