Products

Oil Strainer for the LT77 and R380 five-speed manual gearboxes, located in the rear extension case. Filters the gearbox oil drawn by the internal ...

Plain Washer is a flat load-spreading washer used in the front axle hub and drive shaft assembly. It sits beneath the retaining fastener to distri...

Clevis Pin used to secure a clevis or yoke joint in a mechanical linkage. The pin passes through the yoke and mating rod end and is retained by a ...

Clevis pin

Clevis pin

Clip

Breather Tube for the LT230 transfer box. This tube forms part of the breather system on the LT230 transfer gearbox, routing pressure venting away...

Thrust Washer 1.45mm Diff - LT230

Differential Thrust Washer for the four-pinion differential in the Land Rover-type axle. Seats behind a differential gear to control end-float and...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Fixing Screw used in the flywheel, drive plate and clutch assembly. It is one of the threaded fasteners securing the flywheel or automatic drive p...

Differential Fixing Bolt used on the front and rear axle differential assemblies. It is one of the bolts securing the differential assembly, clamp...

Flanged Screw - threaded fastener with an integral flange head that spreads the clamping load, used in vehicle assembly.

Latch hood

Bonnet Release Latch

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

Hub Bearing is the wheel hub bearing used in both the front and rear axle hubs. It supports the hub on the stub axle and allows the hub and road w...

Hub Bearing is the wheel hub bearing used in both the front and rear axle hubs. It supports the hub on the stub axle and allows the hub and road w...

Clutch Release Spirol Pin is a coiled spring (spirol) roll pin used in the clutch release mechanism. It locates and retains the release fork again...

Front Wheel Stud secures the road wheel to the front hub. The threaded stud is pressed into the hub flange and carries the wheel nut, locating the...

Gearbox Oil Seal seals the bell housing of the R380 5-speed manual gearbox. Running on the input shaft at the front of the gearbox, it retains tra...

Selector yoke spherical bush

Shaft coupling

Layshaft Bearing for the R380 five-speed manual gearbox. This taper roller bearing supports the layshaft (countershaft) within the gearbox casing, ...

Synchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...

Layshaft Taper Roller Bearing supports the front of the layshaft in the manual gearbox. This is the grooved front bearing, sized 31.75 x 62.0 mm. ...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Extension Seal for the R380 5-speed manual gearbox. This is the output shaft oil seal, fitted in the rear extension housing of the gearbox where th...

Extension Seal for the R380 5-speed manual gearbox. This is the output shaft oil seal, fitted in the rear extension housing of the gearbox where th...

Bolt brake caliper front 10.9

Layshaft Bearing is the layshaft taper roller bearing for the LT77 and R380 5-speed manual gearbox. Located in the gearbox centre plate, it suppor...

Housing Bearing

Front Hub Assembly, left-hand side, for the front axle. It carries the front wheel bearing and provides the mounting flange for the road wheel and ...