Products

Door Check Pin - the pivot pin that retains the door check link (check strap) to its mounting bracket on the body pillar. The check link limits ho...

Door Check Arm Pin for the door check strap assembly. This pin secures the door check arm to its mounting bracket on the body, retaining the arm t...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Bolt Threaded fastener used within the exhaust system assembly.

Bolt - 3/8" UNC x 1-1/4" is a UNC hex head bolt used in the front axle assembly of Land Rover vehicles. Used to secure the track rod damper bracke...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Rear End Door Seal seals the rear end door (tailgate) aperture against the surrounding body. This moulded rubber seal fits around the rear body ap...

Fitment: All V8 EFi petrol models from (VIN) XA410482 on

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Brake Pipe Connector - a junction fitting in the hydraulic brake circuit that joins rigid brake pipes. It provides a sealed connection between bra...

Clip - retaining for rubbing strip - rear quarter

Plastic Clip is a retainer clip for the front windscreen lower finisher trim. It secures the lower plastic finisher panel to the windscreen surround.

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Exterior Mirror Glass - Left-Hand, Convex - replacement glass for the left-hand exterior door mirror. The convex profile gives a wider rearward fi...

Mirror Glass - Exterior Door Mirror - Right Hand for the Range Rover P38 exterior mirror assembly. This is the replacement glass insert for the ri...

Mirror glass LH

Clip - Tailgate Finisher is a retaining clip for the upper tailgate finisher trim. It secures the finisher panel to the tailgate.

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Cubby Box Lid Damper - the damper for the centre console cubby box lid. Fitted at the lid hinge, it controls the opening motion so the lid rises s...

Decal - Bonnet - Basalt Edition for the Range Rover P38. This is the bonnet decal specific to the Range Rover P38 Basalt special edition. It repli...

Front Grille Badge in gold finish, fitted to the front radiator grille panel. The badge mounts to the grille to carry the marque identity at the f...

Clip - a retaining clip used to secure finisher mouldings and column shroud panels to their supporting structure. It locates and holds the mouldin...

Air Conditioning Pressure Switch for the R134a refrigerant circuit. Installed in the air conditioning system, it monitors refrigerant pressure and...

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Foam Pad - Plenum - the foam insert that sits in the plenum chamber at the base of the windscreen, beneath the scuttle panel. It filters debris fr...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.

Mud Flap for the rear wheel arch, right-hand side. Fitted behind the rear wheel at the lower body, the flap deflects road spray, mud and stone deb...

Mud Flap for the rear wheel arch, left-hand side. Fitted behind the rear wheel at the lower body, the flap deflects road spray, mud and stone debr...

Circlip a spring-steel retaining ring that seats in a machined groove to axially locate a component on a shaft or within a bore. Used in the diffe...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Door Mirror Housing Cover is the outer cover that fits over the exterior door mirror housing. It clips to the mirror body to form the back shell o...

Mirror Housing - the outer shell of the right-hand exterior door mirror assembly. It mounts to the mirror base on the door and encloses the mirror...

Exterior Door Mirror Glass for the door mirror assembly. The replaceable mirror glass fits into the exterior door mirror housing, restoring the re...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...