Products

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Exhaust Manifold Stud for TDV6 2.7 and 3.0 and TDV8 3.6 diesel engines, used to fasten the exhaust manifold to the cylinder head. On 2.7 TDV6 engi...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Banjo Washer for the oil feed pipe banjo union at the turbocharger, used on TDV6 2.7L/3.0L and TDV8 3.6L/4.4L diesel engines. This sealing washer ...

Gasket - Oil Tube

Injector Retaining Bolt - M6 x 35 mm clamp bolt in the fuel injection system of the V6 and V8 diesel engines. The bolt secures the injector hold-d...

Bolt - Special is an M22 metric timing gear bolt used in the engine timing gear assembly. This special bolt secures components within the timing g...

Bolt - Special is an M22 metric timing gear bolt used in the engine timing gear assembly. This special bolt secures components within the timing g...

Cap Fuel Rrsport, Rrevo - Discovery 3, Discovery 4

Wiper Blades - Pair

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Battery - Wet Non-Spillable for the vehicle electrical system. It is a flooded (wet) lead-acid battery of sealed, non-spillable construction. It su...

Battery - Wet Non-Spillable for the vehicle electrical system. It is a flooded (wet) lead-acid battery of sealed, non-spillable construction. It su...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Bolt - M6 x 35 - a threaded fastener with a 6 mm metric thread and a 35 mm length. Used to clamp and secure components together at points where th...

Cylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Brake Pads - With Springs

Front Brake Pad Set - friction pads for the front axle braking system. Ceramic-based pads that clamp against the front brake discs under caliper p...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Front Brake Pad Set - the friction pads for the front-axle disc brakes. The pads sit in the caliper and are clamped against the brake disc by the c...

Front Brake Pad Set for the front axle. Supplied as an axle set of disc brake pads for the front calipers, together with the pad fitting springs. ...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Screw - a No. 8 x 1" self-tapping screw used to secure the wing-top air intake grille. It fastens the air intake grille to the top of the front wi...

Dzus Fastener is a quarter-turn quick-release stud used to secure the radiator cowl and cooling fan shroud within the engine cooling assembly. The...

Bracket - Mtg

Mounting Bracket - support bracket in the suspension system. Secures suspension components to the chassis. Used in air suspension and active anti-...

Rubber Mount - isolating mount in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and noi...

Rubber Mount - isolating insulator in the suspension system. Cushions and locates suspension components against the chassis, damping vibration and...

Sunroof Finisher is a trim finisher for the sunroof assembly. It frames the edge of the sunroof aperture, concealing the join between the sunroof ...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

High-Tensile Hexagon-Head Bolt - an imperial 7/16" UNF fixing bolt, 2-1/2" long, in high-tensile grade. A general-purpose hex-head fastener with a...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Firtree Clip - a push-in fastener with a ribbed, fir-tree profile that grips into a pre-drilled panel hole. Used to secure trim panels, wiring loo...

Bolt - M8 x 50 - Torx is an M8 threaded fastener, 50 mm long, with a Torx drive head. It is used as a general-purpose fixing across a range of bod...

Engine Gasket & Seal Conversion Set for the 3.0-litre AJV6 / TDV6 diesel engine. A conversion (overhaul) set of gaskets and seals used during ...

Mirror Motor - Exterior Rear View is the drive motor that powers adjustment of the exterior door mirror. Mounted within the door mirror housing as...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Piston Assembly for the 5.0L supercharged V8 petrol engine, supplied as a single standard-size assembly. Eight are required for a complete engine.