Products

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Gasket kit carburettor Zenith Stromberg 175CD

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Splined End

Constant Velocity (CV) Joint for the front axle, in the non-ABS configuration. It sits at the outer end of the front halfshaft, within the swivel h...

This taper roller bearing is designed for installation in the lower swivel pin housing, providing controlled rotational support and load distributi...

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston - Stainless Steel is a 41mm stainless steel piston that operates in the front brake caliper, part of the braking hydraul...

Bleed Screw for the imperial-specification front and rear brake calipers on the Range Rover Classic. This imperial-thread bleed screw fits the cal...

Split Pin used on a front-axle assembly to lock a castellated nut. The pin passes through the drilled fastener and the slots of the nut, and its le...

Anti-Rattle Spring for the front disc-brake caliper. It holds the brake pads under light tension inside the caliper, taking up free play so the pad...

Brake caliper piston rear

Caliper - Piston

Improve your Defender 90, Discovery 1, or Range Rover Classic's braking performance with this stainless steel rear caliper piston.

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Cap adjusting

Gearbox Gasket Set for the LT95 four-speed gearbox fitted behind the V8 petrol engine. The LT95 is a combined main gearbox and transfer unit. The ...

Heater Matrix for the cabin heater assembly, mounted inside the heater box within the HVAC housing. Engine coolant is circulated through the matri...

Steering Column Top Shim used in the steering column assembly of the Range Rover Classic. This shim is fitted at the top of the steering column to...

Joint Washer for the manual gearbox top cover. This gasket seals the joint between the top selector cover and the gearbox case, retaining the gearb...

Axle Pinion Gasket for the Salisbury rear axle, sealing the pinion bearing retainer to the differential housing at the propshaft flange end of the ...

Steering Valve Ring is a PTFE sealing ring used within the rotary valve of the Adwest power steering box. It seals between the pressure lands of t...

Differential Crown Wheel and Pinion Set for the LT95 four-speed gearbox used on V8 applications. The set provides the matched crown wheel and pini...

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Temperature Sensor mounted in the air filter (air cleaner) housing. This thermal sensor unit sits within the air intake housing and responds to th...

Vacuum unit

Cold Start Solenoid for the carburettor cold-start enrichment circuit on the V8 petrol carburettor induction system. The solenoid operates the col...

Fuel Filler Cap Seal for the fuel system of the Range Rover Classic. This rubber seal fits the hinged (flip-up) fuel filler cap and creates a fuel...

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

GENUINE LR camshaft sprocket for Rover V8 engines

Carburettor Gasket sealing the inlet manifold adaptor elbow to the carburettor on the Rover V8 twin-carburettor petrol engine. Fitted between the ...

Thermostat Housing Gasket seals the thermostat housing (water outlet elbow) to the intake manifold on the 3.5L carburettor V8 engine. It sits in t...

Rocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...

Drive Belt (V-belt) for the engine accessory drive system, transferring rotation from the crankshaft pulley to a driven accessory. This is a 13 mm...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Rocker Shaft Assembly forms part of the valvetrain (rocker gear) on the overhead-valve V8 petrol engine. Mounted on pedestals above the cylinder h...