Products

Inlet Heater Hose - 300TDi - RHD

A/C Condenser sits in the air-conditioning refrigerant circuit, mounted at the front of the vehicle ahead of the radiator. High-pressure refrigera...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Facia Louvre Vent Housing for air-conditioned models, mounted in the facia as part of the cabin air distribution system. It carries the directiona...

Decal name plate

Heater Hose forming part of the engine cooling and cabin heating circuit. This hose connects within the heater circuit, routing coolant between th...

Heater Hose - Heater Matrix to Control Valve forming part of the engine cooling and cabin heating circuit. This hose runs between the heater matri...

Heater Hose - Coolant Valve is a moulded coolant hose in the heater circuit of the engine cooling system. It connects the heater control (coolant)...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Heater Hose - Inlet carries engine coolant into the cabin heating circuit, feeding the heater matrix that warms air inside the HVAC housing. On th...

Heater Hose - Outlet returns engine coolant from the cabin heating circuit back to the engine cooling system after it has passed through the heater...

Heated Windscreen - a laminated front windscreen with an integral electric heating element. The embedded element clears frost, ice and misting fro...

Caliper Bolt is the fixing bolt that secures the brake caliper to its mounting bracket. The same bolt specification is used across several chassis...

Hexagon Bolt - an M10 x 45 mm high-tensile bolt, property class 10.9, used in the suspension top link, fulcrum and ball joint assembly. The 10.9 g...

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Camshaft Bolt for the 2.5L 300 Tdi diesel engine. Retains the camshaft drive gear on the camshaft within the timing drive.

Hexagon Bolt - an M16 x 100 mm high-tensile bolt, property class 10.9, used to secure the front radius arm. The 10.9 grade provides the high clamp...

Link Clip - an anti-rattle clip for the side door latch linkage. It retains the latch operating rod within the door lock mechanism, holding the li...

O-Ring for the R380 five-speed manual gearbox extension case. Seals the oil pump within the gearbox extension housing.

Grommet - moulded rubber grommet for a panel or component aperture. Fitted into a drilled or pressed hole to line the opening, it provides a seal ...

Castor Correction Kit - 44mm Wide Bush for the front suspension radius arm assembly on the Defender, Discovery 1, and Range Rover Classic. Lifting...

Circlip a spring-steel retaining ring that seats in a machined groove to axially locate a component on a shaft or within a bore. Used in the diffe...

Reverse switch R380 Frl.1 manual

Hose Clip - 12-20mm worm-drive hose clip suitable for hoses with an outside diameter of 12 to 20mm. This stainless-steel screw-type clip tightens ...

Hose Clip is a worm-drive band clamp used to secure flexible rubber hoses onto rigid pipe spigots and unions across the coolant, heater, fuel and i...

Jubilee Clip - 21-44mm is a worm-drive hose clip with a 21-44mm clamping range. The band is tightened by a captive worm screw to clamp small- to m...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Hose Clip - Jubilee - 70-92mm is a worm-drive band clamp with a clamping range of 70-92 mm. It secures a hose over its spigot or connector, compre...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Exhaust Olive is a tapered sealing ring used at the exhaust system's pipe joints. It seats between two pipe sections at a compression joint, formi...

Harness Edge Clip that routes and secures the wiring harness within the facia and centre console area. The clip attaches to a panel edge and retai...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

Front Door Glass Guide is a moulded plastic guide that locates the front door drop glass within its window channel. Fitted inside the door frame, ...

CuNiFer Clutch Pipe, 1/4" outer diameter, supplied for the clutch hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough t...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...