Products

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Edge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...

Plastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...

Striker Plate

Bush GENUINE LR sold EACH! for fitting air intake grille 90/110/130 and for fitting old type individual letters "Range Rover"

Bush

Bonnet Catch, the bonnet safety catch assembly mounted at the front of the engine bay. It engages the bonnet as a secondary retention after the pr...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Engine Plug is a core (welch) plug that seals the casting holes in the engine. Fitted to the cylinder block, cylinder head water jacket and inlet ...

Sedimentor O-Ring for the diesel fuel filter assembly. This rubber sealing ring seals the sedimentor bowl against the filter head, preventing fuel...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

Fuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...

Plain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...

Rear Wheel Arch Front Extension - RH is the front section of the right-hand rear wheel arch extension for 2-door bodyshells. It forms the leading ...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Front Wing Mounting Rail for the right-hand side. This rail forms the upper mounting line for the front wing, providing the fixing points along wh...

Front Wing Mounting Rail for the left-hand side. This rail forms the upper mounting line for the front wing, providing the fixing points along whi...

Side Window Insert Spring Tensioning spring for the sliding side window insert in the two-door body's side window assembly. It provides the retain...

Door Control Unit - 2-Door

Outer Sill - external sill panel for the right-hand side of the two-door body. The outer sill is the visible rocker panel spanning the lower body b...

bracket 390384

Dash Assembly Bracket - a structural support bracket forming part of the dashboard (fascia) assembly. The bracket provides a fixing point within t...

Front Door Hinge mounts the front door to the body pillar, carrying the door's weight while allowing it to pivot open and closed. The hinge locate...

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Fresh Air Grille Finisher for the fresh air intake, left-hand side. This capping finisher trims the fresh air intake grille on the body, covering ...

Interior Door Pull Handle for the front right-hand door of the Range Rover Classic 2-Door Station Wagon. This is the inner grab handle mounted on ...