Products

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Rear Mudflap Mounting Angle, the angled bracket that secures a rear mudflap to the underbody. It positions and supports the mudflap behind the rea...

Gearbox Gaiter Grommet seals the point where the high/low transfer lever passes through its gaiter on the LT95 four-speed gearbox. Fitted to the t...

Door Hinge Bolt A fixing screw for the front door hinge, part of the door hinge mounting hardware. It secures the hinge to the body pillar and doo...

Mounting Angle is the left-hand front bracket within the front wing and deck panel assembly. The angle bracket locates and supports the front wing...

Mounting Angle is a front bracket within the front wing and deck panel assembly. The angle bracket locates and supports the front wing and deck pa...

Wing Seal A rubber sealing strip fitted to the inner wing. It seals the joint at the wheelarch and valance to keep out water and road debris.

Door Lock Assembly - RH for the Range Rover Classic 2-Door Station Wagon. Fitted to the right-hand door, this lock unit provides the latching and ...

Bonnet Buffer for the Land Rover bonnet assembly. This rubber buffer mounts to the body structure and provides a cushioned contact point for the u...

Bonnet Release Cable for the Range Rover Classic. This cable runs from the interior release handle to the bonnet catch, allowing the bonnet to be ...

Roll Pin for Door Hinge on the Range Rover Classic. A small cylindrical spring pin that locates and retains components within the door hinge assem...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Windscreen Filler Strip closes and trims the gap between the windscreen glass and the body aperture, forming part of the windscreen sealing and fin...

Tailgate Seal - the weather seal for the upper tailgate, part of the rear body closure assembly. Fitted around the upper tailgate aperture, it for...

Tailgate Seal - the weather seal for the upper tailgate, part of the rear body closure assembly. Fitted around the upper tailgate aperture, it for...

Upper Tailgate Lock Barrel & Key secures the upper tailgate (load door) and provides key-operated locking. Supplied as the lock barrel with it...

Rear Window Sealing Pad for the Range Rover Classic. This rubber pad seals the rear side window aperture, preventing water ingress and wind noise ...

Mudflap Bracket for the front, right-hand side. This bracket secures the front mudflap to the body, holding it at the correct position behind the ...

Mudflap Bracket - Front - LH secures the front mudflap to the body on the left-hand side of the vehicle. Part of the front mudflap assembly, the b...

Front Door Hinge Set Screw secures the front door hinge to the body pillar and door within the door mounting hardware. It clamps the hinge leaf in...

Edge Clip A black edge clip with a delta-section profile that grips a panel flange. It provides a push-on fixing along the edge of the door assemb...

Window Catch Bush for the Range Rover Classic. A small rubber bush fitted to the rear window catch mechanism, cushioning the catch contact point a...

Warning Label A warning label relating to the battery negative (earth) cable connection. It is applied in the vehicle to convey a safety instructi...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Nut A 4BA hex nut used as a threaded fastener. Applied on the door lock linkage and rear bumper mountings.

Plain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

In/out member spring

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Tappet kit

Cap Reservoir Br.m.cylinder

Clutch Slave Cylinder Repair Kit overhauls the clutch slave cylinder within the hydraulic clutch release circuit on the LT77 manual gearbox. The s...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Spring plate

Locking plate

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...