Products

Check Strap for the rear suspension assembly. The check strap limits the downward travel of the axle on droop, preventing the leaf springs from ove...

Bolt, a threaded fastener used on the 2.0L petrol engine.

Bolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Bolt, 7/16" BSF x 1-3/8" secures the upper swivel pin to the swivel housing in the front axle assembly. The top swivel pin retains the swivel ball...

Warning Light - Red for the dashboard instrument panel. Lucas WL3 type red panel warning light indicator, used on classic Land Rover dashboards as...

Cone Bearing - Swivel Housing for the front axle swivel pin assembly. Sits within the swivel housing to support the swivel pin on early Series Lan...

Swivel Pin

Layshaft Split Ring Halves are a matched pair of semi-circular retaining ring halves used in the Land Rover Series I and II gearbox assembly. The ...

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Exhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Exhaust Bracket for the exhaust system on left-hand drive vehicles. This bracket supports and locates the exhaust along its run beneath the vehicl...

Suspension Damper

Exhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Clutch Anchor Plate - a steel mounting plate within the clutch pedal box assembly. It anchors the clutch pedal pivot to the bulkhead, providing th...

Spring Road Front SWB 9lf DS

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Master Cylinder for the hydraulic brake circuit on early Series I Land Rovers. The master cylinder converts mechanical pedal force into hydraulic p...

U-Bolt - a rear leaf-spring axle clamp. It passes around the axle tube and clamps the rear leaf spring to the axle seat via the lower spring plate...

Front Towing Eye / Lifting Ring bolts to the front of the chassis, providing an anchored attachment point for towing, recovery and lifting. The ri...

Stub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Top Swivel Pin Bearing Spring, part of the front axle swivel pin housing assembly. The spring acts on the top swivel pin bearing to maintain beari...

spring road front SWB 9 leaf Passenger Side

Plain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...

Front Spring Dowel for the 9-leaf front road spring, part of the leaf spring suspension assembly. The dowel is the centre locating pin that passes...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the right-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the drum brake assembly - the left-hand hydraulic slave cylinder that operates the brake shoes. The same cylinder serves either ...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, right-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hy...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Wheel Cylinder for the rear drum brake assembly, left-hand side. The wheel cylinder forms part of the hydraulic drum brake circuit, converting hyd...

Output Shaft - Front for the Land Rover transfer gearbox. The front output shaft carries drive from the transfer gearbox to the front propshaft, su...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Front left-hand wheel cylinder for the hydraulic front braking system, installed within the brake backplate assembly of 11-inch front brake configu...