Products

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Stop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...

Exhaust Bracket Saddle Clamp for the intermediate exhaust pipe on 109-inch wheelbase Series 2 and Series 3 Land Rovers. The saddle clamp locates an...

Sealing Ring A rubber O-ring sealing ring serving two separate shaft and tube interfaces. It is used on the transfer box high/low range selector s...

Leaf Spring - Front - 11-Leaf A semi-elliptic front leaf spring built up from an eleven-leaf pack, part of the front suspension. It carries the ch...

Valve Seat Insert for the 2.6L 6-cylinder engine used in Series II, IIA, and III Land Rovers. Pressed into the cylinder head, the valve seat insert...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Clutch Slave Cylinder for the hydraulic clutch actuation system. Mounted on the gearbox bellhousing, this cylinder receives hydraulic pressure fro...

Transfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...

Spring - Timing Ratchet sits within the engine timing assembly on Land Rover 2.25L and 2.0L diesel engines. This spring provides the retention for...

Fuel Sediment Bowl for the fuel system on Series II, IIA, and III Land Rovers, including the 101 Forward Control. The glass bowl mounts below the f...

Mainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...

Thrust Washer - 0.128" A gearbox mainshaft thrust washer for the second-speed gear, 0.128" thick. It controls the end-float of the 2nd-speed gear ...

Thrust Washer - 0.128" A gearbox mainshaft thrust washer for the second-speed gear, 0.128" thick. It controls the end-float of the 2nd-speed gear ...

Thrust Washer - 0.130" A gearbox mainshaft thrust washer for the second-speed gear, 0.130" thick. It controls the end-float of the 2nd-speed gear ...

Thrust Washer for the 2nd gear assembly within the manual gearbox. Fitted to the mainshaft to control the end float of 2nd gear, the washer is sel...

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Rocker Cover Gasket (Exhaust Side) - seals the exhaust-side rocker cover joint on the 2.0L IOE (inlet-over-exhaust) engine. Fitted between the roc...

Sump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...

Rocker Cover Gasket sealing the inlet rocker cover to the cylinder head on the 2.0L petrol IOE (Inlet Over Exhaust) engine. Fitted between the upp...

Rocker Cover Gasket sealing the inlet rocker cover to the cylinder head on the 2.0L petrol IOE (Inlet Over Exhaust) engine. Fitted between the upp...

Joint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...

Sealing ring

Radiator Top Hose forms part of the engine cooling circuit, connecting the top tank of the radiator to the coolant outlet at the cylinder head. Th...

Radiator Hose serves as the lower radiator hose in the cooling system of Series I Land Rovers built between 1948 and 1958. This hose connects the ...

Valve Cup for the valve gear of the 3-bearing 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The cup seats on the top ...

Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...

Brake Lining - Rear is a replacement friction lining for the rear drum brake assembly on long-wheelbase Land Rover models, covering 109-inch, 110-i...

Gerschikt voor 2.25 ltr benzine

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Track Rod Assembly - 111 cm is the front axle track rod for Series II Land Rovers, connecting the two front steering knuckles to maintain correct t...

Heater hose SII IIA Genuine

Distance piece

Oil Filter Bowl Bolt Washer - rubber sealing washer for the oil filter bowl centre bolt. Fitted to the centre bolt that retains the oil filter bow...

Water Pump - 2.0 IOE - the engine coolant pump in the cooling system, for the 2.0L IOE (inlet-over-exhaust) petrol engine. Driven by the fan belt ...

Lock Washer is a folding lock tab used in the front axle swivel pin housing assembly. Fitted beneath a 3/8" stud fixing, the tab is bent up agains...

Shackle plate

Shackle pin

O-Ring Seal - sealing ring for the steering box rocker shaft. Fitted around the rocker (sector) shaft where it passes through the steering box hou...

Retainer