Products

Shim is a 0.002" adjustment shim for the manual (non-power-assisted) steering box. It is fitted within the steering box to set the correct end-flo...

Ball Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...

Fluid Reservoir for the hydraulic braking and clutch system on the early Land Rover Series I. This metal reservoir feeds the Girling master cylinde...

Engine Mounting Bracket for the left-hand side of the engine, part of the engine mounting system. The bracket bolts to the left-hand side of the c...

Engine Mounting Bracket - right-hand front engine mount angle adaptor. Bolts to the right-hand side of the cylinder block and carries the rubber e...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Pedal Shaft is the transverse shaft on which both the clutch pedal and brake pedal are mounted within the cab, on vehicles without a brake servo. ...

Top cover

Pedal Pivot Bush is the bearing bush on which the clutch or brake pedal pivots within the pedal box assembly. Pressed into the pedal bore, it prov...

Clutch Pedal Box Top Gasket for the clutch pedal housing on manual transmission vehicles. This gasket seals the joint between the clutch pedal box...

Differential Crown Wheel Locking Tab is a tab washer used in the axle differential assembly to lock and retain the crown wheel bolts after tighteni...

Crown Wheel Bolt with British Standard Fine (BSF) thread, used to secure the crown wheel to the differential carrier in early Land Rover axles. Tw...

Leaf Spring Heavy Duty

Rear Leaf Spring - heavy-duty rear leaf spring for the passenger side, built with eight leaves for increased load capacity. Locates the rear axle ...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Rocker Shaft for the 2.6L six-cylinder petrol engine, part of the valvetrain in the cylinder head. The shaft mounts on the head and carries the ro...

Exhaust Rocker Shaft is the shaft on which the exhaust rocker arms are mounted within the cylinder head valve train of the 2.6L 6-cylinder petrol e...

Banjo bolt

Manifold Gasket for the 2.25L and 2.5L 4-cylinder petrol engines. This gasket seals the combined inlet and exhaust manifold assembly to the cylind...

Cylinder Head Gasket - non-adhesive type, for the 2.25-litre petrol engine. Seals the joint between the cylinder head and the cylinder block, cont...

Coil Spring - Rear for the rear suspension. It supports the vehicle weight carried over the rear axle and sets the rear ride height. This is a rai...

Handbrake Drum is the drum for the transmission-mounted parking brake, for use with the LT76 gearbox. Mounted at the rear of the gearbox on the tr...

Coil Spring - Front for the front suspension. It supports the vehicle weight carried over the front axle and sets the front ride height. This is a...

Camshaft for the Land Rover 2.25L four-cylinder diesel engine, early specification (up to engine number 36619420B), and also applicable to the 2.0L...

Valve Rocker for the Land Rover 2.25L four-cylinder diesel engine - right-hand exhaust rocker arm. Pivots on the rocker shaft in the cylinder head ...

Rocker Cover Gasket for the 2.6L six-cylinder petrol engine, sealing the side rocker cover to the cylinder head. It forms the oil-tight joint alon...

Exhaust Packing Plate for the exhaust mounting strap assembly. It sits between the exhaust strap and its chassis bracket, packing the joint so the...

Front Coil Springs - heavy-duty replacement pair for the front suspension. Shot peened, double scragged and load tested for consistent spring rate ...

Clevis Fork is the forked end fitting used in the handbrake actuation linkage. It joins the handbrake rod to the operating lever, with a clevis pi...

Timing Chain Vibration Damper for the front timing chain drive on four- and six-cylinder engines. Mounted within the timing cover, it bears agains...

Fuel Pipe Sealing Washer seals the fuel pipe union at the DPA diesel injection pump. Fitted at the union connection, it is compressed between the ...

Rear Coil Spring Pair - heavy-duty load rating - for the rear suspension assembly. The springs seat in the rear spring towers between the axle perc...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Oil Feed Pipe is the external oil feed pipe supplying the cylinder head within the engine lubrication system. It carries pressurised oil from the ...

Wheel Cylinder Repair Kit for overhauling a front drum-brake wheel cylinder with a 1.25 inch bore. It restores the hydraulic seal of a worn or lea...

Front leaf spring LWB diesel DS

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Exhaust Pipe - Intermediate - Non-Station Wagon

Rear Coil Spring Pair - medium load rating - for the rear suspension assembly. The springs seat in the rear spring towers between the axle perches ...

Inlet Air Seal for the Solex carburettor connection on the 2.25L 4-cylinder petrol induction system. Seals the joint between the air intake and th...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Front Coil Springs HD Pair

Swivel Housing Gaiter Kit in leather for the front axle swivel housings, supplied as an axle set to cover both sides. The gaiter encloses the swiv...

Carburettor Bell Crank Bush for the accelerator throttle linkage on the 2.25L 4-cylinder petrol engine. The bush locates the throttle bell crank a...

Past op  1958 - 61:   Sommige S 3 vanaf 1977 en 110 1983 - 84 All 3 Lug Internal Fixings