Products

Bonnet Canvas Rest Strip for the front body assembly. This canvas strip mounts across the top of the radiator/front panel, forming the surface the ...

Cleat Rope Hook Body Side All and Classic (Softtop) - Series Defender

Gear Lever Gaiter for the transmission tunnel. This flexible boot fits around the base of the gear lever where it passes through the tunnel, sealin...

Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Panel Rivet - a round-head solid rivet for body panel fixing. Used to join body panels and brackets, it has a domed (round) head, a 3/16 in shank ...

Washer

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Rivet, semi-tubular with a semi-round (truss) head, 3/16 in diameter and 3/8 in long. It secures door weatherstrip and seals to the body aperture....

Chain Bracket Series/Lw

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Plain Flat Washer for use beneath bolt heads or nuts where specified. Used across multiple assemblies including alternator mountings, exhaust manif...

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

Tailgate Seal for the lower edge of the rear tailboard. It seats along the bottom of the drop-down tailgate and seals against the body, keeping wa...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Rope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Rear Quarter Seal - the rubber glazing seal that secures the fixed rear quarter window into the hard-top body aperture. Sized for 5mm glass, it be...

Interior Grab Handle - interior pull handle for the rear side door, used to draw the door closed from inside the cab. It fixes to the inner face o...

Rear End Door T-Handle and Lock Assembly for the upper tailgate on hard top body configurations. The handle operates the latch mechanism to release...

Door Clevis Pin for the door check strap mechanism. The pin locates the check strap to its mounting bracket, forming the pivot the strap works aga...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Coil Spring Carrier for the 2.0-inch coilover shock assembly. The carrier retains the coil spring on the coilover body, locating the spring between...

Coil Spring Carrier for 2.5in remote reservoir coilover shock absorbers. This component locates and supports the coil spring around the body of th...

Washer

Heater Blower Motor supplied without wiring lead (motor body only). This 12V electric motor drives the centrifugal fan within the heater blower un...

Ignition Switch Knob - the rotary knob for the PRS-type combined ignition and lighting selection switch. It fits onto the switch spindle to provid...

Floor Panel Screw with a mushroom head profile, used to secure floor plates and lower rear body panel assemblies on the Defender. The low-profile ...

Floor Panel Screw x 100

Upper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...

Rod Guide Bearing Cap Seal (Nok) 2.0

Rod Guide Bearing Cap Seal (Nok) 2.5

Guide Rod 2.5 Coilover (12 19 On)

Guide Rod 2.0 Coilover (08 19 On)

Bush Guide Rod 2.0 Coilover (08 18 On)

Bush Guide Rod 2.5 Coilover (08 18 On)

Dust Seal 2.0 Coilover (05 18 On)