Products

Dust Seal 2.5 Coilover (08 18 On)

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Rear Mudflaps - a pair of rear mudflaps for the 88in short-wheelbase, fitted behind the rear wheels to deflect road spray and debris thrown up by t...

Front Mudflaps, supplied as a pair. The mudflaps mount behind the front wheels to deflect road spray, mud and stones thrown up by the tyres, prote...

Guide Rod Washer for 2.0in remote reservoir coilover shock absorbers. This washer locates on the guide rod of the coilover unit, providing the cor...

Guide Rod Washer for 2.5in remote reservoir coilover shock absorbers. This washer locates on the guide rod of the coilover unit, providing the cor...

Lower Tailgate for the rear of the body - the drop-down tailboard panel that closes off the rear of the load area. Hinged along its lower edge, it...

Interior Lamp Lens for the interior courtesy lamp. The translucent lens clips over the lamp body, protecting the bulb and diffusing its light into...

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Barrel Lock and Key, Set of Three for the door locks, supplied as three keyed lock barrels each with a key. Each barrel is the cylinder the key tu...

Bench Seat Backrest in black vinyl, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts to ...

Bench Seat Backrest in techno fabric, forming the upright back section of the folding rear load area bench seat. This 810mm wide backrest mounts t...

Two-Man Bench Seat Cushion for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the two-s...

Rear Bench Seat Cushion in grey twill fabric, forming the base section of the folding rear load area bench seat. This 810mm wide cushion provides ...

Bench Seat Cushion - Techno Trim for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the...

Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...

Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...

Rear Folding Bench Seat - a complete rear bench seat assembly that folds to free up the load area when not in use. Finished in black vinyl, which ...

Rear Bench Seat Assembly in grey vinyl, comprising a cushion, backrest, frame, and fitting kit for direct installation in the rear load area. The ...

Rear Seat Assembly - a two-seater rear bench seat upholstered in grey twill vinyl, for the rear passenger area of Defender and Series Land Rover ve...

Rear Folding Bench Seat - a complete rear bench seat assembly that folds to free up the load area when not in use. Finished in Techno-style uphols...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End (Right-Hand) is the ball-joint connector at the end of the steering track rod, linking the track rod to the steering arm. It transmi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Track Rod End with left-hand thread, part of the steering linkage. The track rod end connects the track rod to the steering arm through a ball joi...

Transfer Box to Gearbox Mounting Stud, 2" length, used to fasten the transfer case to the rear of the main gearbox casing. This stud forms part of...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Swivel Ball Taper Plug for the front axle swivel housing. This tapered-thread plug screws into a port in the swivel ball housing, sealing it agains...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Front Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...

Front Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...

Upper Door Hinge for the right-hand door, forming the upper pivot of the door-to-body mounting. Fitted as the upper member of the door's two-hinge...

Door Cap (Galvanised, Right-Hand) is the capping rail that forms the top edge of the right-hand front door frame around the window aperture. The g...

Door Cap (Galvanised, Left-Hand) is the capping rail that forms the top edge of the left-hand front door frame around the window aperture. The gal...

Rubber Buffer for the door-top sliding side window. The buffer fits at the top of the door and acts as an end-stop for the sliding glass, limiting...

Door Top Seal Strip for the front door assembly. This rubber seal runs along the upper section of the door frame, sealing the gap between the door ...

Door Top Glass Retainer for the front door glazing assembly of Series Land Rovers. This retainer secures the top edge of the fixed front door wind...

Teflon Band 2.0 Coilover (12 17 On)

Teflon Band 2.5 Coilover (12 17 On)

Filler Strip for the door top. The strip fits along the top edge of the door, closing and finishing the joint at the door-top glass frame and seal...

Filler Strip Spacer for the door top, fitting at the vertical joint of the door-top glass frame. The strip fills and finishes the vertical gap in ...

Rear Side Skin - Left Hand Side for the rear body assembly of Series Land Rovers with the 88" wheelbase. This outer body panel forms the lower rea...

Wing Stay for the rear body structure of the Series Land Rover. This right-hand steel bracket braces the rear wing to the body sill, providing str...

Sill Panel (5" Deep, Front, Right-Hand) is the lower body panel that runs along the right-hand front body side beneath the door aperture. It forms...