Products

Tailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...

Tailgate Hook for the lower hinged tailboard, left-hand side. This pigtail (spiral) hook mounts on the body and retains the tailboard chain, holdi...

Rear Wing Stay for the rear body assembly of Series II, IIA, and III Land Rovers (1958-1985). This stay bracket braces the rear wing against the b...

Fitment: all models to 1980

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Rear Door Seal - rubber weatherseal for the rear door aperture. This rubber seal fits around the rear door opening, sealing the closed door agains...

Floor Mounting Pad is a 5mm rubber spacer pad used at the rear body floor support mounting, fitted between the body and the chassis-mounted support...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Spacer

Hood Fixings - hood stick set for the full canvas hood on Long Wheelbase Series vehicles. Hood sticks are the metal bows that form the internal st...

Door Trim Retainer - lower horizontal retainer for the rear end door window. This retainer secures the lower edge of the glass within the rear end...

Glass Retainer is the vertical glazing retainer for the rear end door assembly. Holds the rear door glass along its vertical edge.

Door Trim Retainer - upper horizontal retainer for the rear end door window. This retainer secures the upper edge of the glass within the rear end...

Aluminium Corner Strip - the curved top retainer for the rear door glass. One of the aluminium retainers in the rear (end) door glazing set, this ...

Check rod RH

Filler Strip is the fixing channel that runs along the top edge of the rear door window aperture. It locates and retains the upper edge of the doo...

109 stawag B/C post one-piece door seal LH + RH

Door Seal fits along the floor line of the rear side door aperture, sealing the gap between the lower edge of the door and the body sill. It block...

Corner Capping - galvanised - right-hand (offside) roof corner. This galvanised steel capping fits over the offside rear roof corner, covering and...

Corner capping LH S3 galvanised

Rear Door Side Seal - Right Hand Side for the rear body of the 109" Station Wagon. This rubber seal runs along the side edge of the right-hand rea...

Door Seal - Left Hand is a body sealing component fitted to the left-hand door aperture. The seal runs around the door frame and compresses agains...

Rear Body Seal is a rubber seal fitted to the rear body extension panel of the station wagon body. The seal closes the gap between the extension p...

Mounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...

Rubber Seal fits along the joint between the truck cab base and the rear body, sealing where the cab meets the tub. It forms a continuous barrier ...

Bodyside Seal for the lower edge of the rear upper body section, sealing the joint between the upper body structure and the lower body on the rear ...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Clip - a retaining clip within the vehicle body hardware, used to secure and locate a fitted component in position.

Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Hasp for the seat box and rear locker lid. The hasp fastens the lid closed, engaging the turnbuckle on the box body to hold the lid down and seal ...

Turnbuckle is the semi-circular catch that fastens the seat box and rear tub locker lids down. It rotates over the mating hasp to hold the lid shu...

Roof Panel Seal - Right-Hand for the Defender 110 rear upper body, sealing the joint between the right-hand roof panel edge and the upper body stru...

Roof Panel Seal - Left-Hand for the Defender 110 rear upper body, sealing the joint between the left-hand roof panel edge and the upper body struct...

Centre Retainer - Front Windscreen Glass is the metal retainer strip that secures the front windscreen glass at its centre division point. The ret...

Window Channel - Front Door

Window Channel (bailey channel) for the sliding side window glazing assembly. It runs along the edge of the window aperture in the door frame, form...

Clevis Pin for the bonnet stay. Forms the pivot at the upper end of the bonnet prop, retaining the stay to the bonnet.

Circlip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...

Cab Body Panel Mounting Bracket - a body bracket that locates and secures a cab panel to the surrounding body structure. It provides the fixing po...

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...