Products

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Tailboard Seal for the rear tailgate. Seals the vertical closing edge of the tailboard where it meets the body, keeping out water, dust and draugh...

Windscreen Glass - replacement glass panel for the windscreen frame. Fits the windscreen aperture as a direct replacement for cracked or damaged g...

bottom door Series RH Series 3

Door Bottom for the left-hand side, forming the lower section of the door assembly. This is a repair panel that replaces the lower portion of the ...

Exterior Door Handle with Lock Barrel and Keys, right-hand (offside). The complete locking handle for the front door, comprising the external push...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Rear Sill Panel for the right-hand side, a body repair panel in the lower bodyside and chassis structure. The panel forms the rear section of the ...

Rear Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the rear body tub. The panel closes the gap betwe...

Front Sill Panel for the right-hand side, of the narrow sill type. The sill is the structural panel running along the lower edge of the body benea...

Front Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the front body section. The panel closes the low...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Blanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Blanking Plug for closing an unused 16 mm (5/8") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Interior Mirror Bracket mounts the interior rear-view mirror to the body, providing the fixing point for the mirror stem. This is the untrimmed ve...

Bonnet Spring Retaining Clip, part of the bonnet hinge and stay assembly. Retains the bonnet (hood) tension spring against its anchor, holding the...

Side Panel Buffer, a rubber buffer fitted at the rear body side panels. Sits between the upper and lower rear quarter panels, cushioning the joint...

Mounting stud

Handbrake Gaiter for the L-shaped handbrake lever on late Series IIA and all Series III models. Fits the oval aperture through which the lever pass...

Transfer Gear Lever Gaiter for the high/low ratio selector lever on the Series Land Rover transfer box. This rubber gaiter seals around the transf...

Wiper Blades - Pair

Rubber Washer - Window Catch for the sliding window catch assembly on Series II, IIA, and III Station Wagon body variants, produced up to 1984. Th...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Seat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Grommet - Blanking Plug, Gearbox Tunnel for Land Rover Series II and III. This small rubber blanking plug fits into an aperture in the top of the ...

Rubber Washer - Seat Backrest for Land Rover Series and Defender models. This rubber washer is used in the seat backrest assembly, fitting beneath...

Cable Lug - 35mm² - M10 Hole for use in vehicle electrical systems. A crimp-type cable lug designed for 35mm² cross-section battery and power cabl...

Door lock RH

Door Latch Assembly - LH - Front - Non-Locking for Land Rover Series vehicles from 1958 to 1984. This left-hand front door latch assembly fits the...

Interior Door Lock Button, right-hand, of the interior door furniture. The thumbscrew-type lock button that operates the door lock from inside the...

Door Lock Button - LH - Push & Twist for Land Rover Series vehicles from 1954 to 1981. This left-hand push-and-twist door lock button fits the...

Spare Wheel Bonnet Strap, the retaining strap for a bonnet-mounted spare wheel. Secures the spare wheel in the bonnet-top carrying position, holdi...

Interior Mirror for Series Land Rover models. Direct-fit interior rear-view mirror providing rearward visibility from the driver's position inside...

Number Plate Lamp Plinth is the mounting base for the rear number plate lamp, fixing the lamp unit to the bodywork above the number plate. It loca...

Front Wing Panel is the outer body panel that forms the side of the front end over the front wheel arch, part of the front body assembly. Supplied...

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...