Products

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Fuel Filler Seal - sealing ring fitted at the fuel filler, part of the fuel tank filler assembly. Seals the joint at the filler neck to prevent fu...

Stub Axle Gasket for the rear drive shaft assembly on Land Rover Series II, IIA, and III. This gasket seals the stub axle flange at the rear axle ...

Intermediate Exhaust Pipe - the centre section of the exhaust system, connecting the front down-pipe to the rear silencer. Routes exhaust gas rear...

Shim plate

Layshaft First Gear - the first-speed gear on the layshaft (countershaft) of the main gearbox. Meshes with the corresponding mainshaft gear to pro...

Mainshaft Gear - 1st Speed is a 29-tooth first-speed gear that runs on the mainshaft within the manual gearbox gear train. As a non-synchronised c...

Flasher Unit is the 3-pin relay in the direction indicator circuit that switches the turn signal lamps on and off at a regular rate. Wired between...

Flasher Unit for the direction indicator (turn signal) circuit. This is a 12V three-pin thermal, can-type flasher that switches the indicator lamps...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Gasket

Reverse Gate Bracket is the fixed section of the reverse-gate stop within the gear-lever mounting on the Series four-speed gearbox. It forms the g...

Handbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Diesel Fuel Decal is the self-adhesive caution label applied at the fuel filler to identify the tank as diesel. It marks the filler point so the v...

Carburettor Spring - Solex - a spring used in the Solex carburettor of the 2.25 litre petrol engine, part of the fuel system. It supplies the spri...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Instrument Panel Bulb, rated 12V 2W with a BA7s bayonet base (type 281), for the instrument cluster lighting circuit. It provides the internal ill...

Exhaust Connecting Pipe is the intermediate section of the exhaust system, joining the front pipe to the rear silencer. It carries exhaust gas alo...

In/out member spring

Brake Shoe Spring for drum brake assemblies. This return spring draws the brake shoes away from the drum surface when the brake pedal is released,...

Brake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...

Brake & Clutch Reservoir Tank Kit

Distance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...

Shackle Shim Ring - 0.003in shim used to set the gap on extended spring shackles. Fitted against spacer tube 504211 to take up clearance on the sh...

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Fuel Cap closes and seals the fuel tank filler neck on petrol applications. It uses a two-lug bayonet fixing that locates and locks into the fille...

Fuel Cap Locking Hasp is the body-mounted latch in the fuel filler arrangement that secures the petrol filler cap against unauthorised opening. It...

Headlamp bulb 12V 40/45W duplo (non-halogen)

Fuel Filler Cap Seal is the sealing ring fitted inside the metal fuel filler cap. It forms the seal between the cap and the filler neck, preventin...

Lock Nut, 5/16 BSF, a self-locking nut used on the transmission parking-brake assembly. It retains the transmission (handbrake) brake drum, its se...

Self-Locking Nut, 3/8" BSF, used to secure propshaft fasteners within the drivetrain. The deformed thread form provides a self-locking action that...

Plain Nut for use as a standard fastener across Land Rover applications. A plain (non-locking) hex nut for general assembly and repair work.

Exhaust Downpipe is the front section of the exhaust system, connecting the exhaust manifold outlet to the intermediate pipe. This downpipe fits L...

Rocker cover rubber washer petrol

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...