Products

P-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...

Flywheel Ring Gear for four-cylinder petrol engines. The ring gear is shrink-fitted to the periphery of the flywheel and meshes with the starter mo...

Tappet Screw - the valve-clearance adjusting screw in the rocker gear of the four-cylinder engine (3-bearing crankshaft), part of the valvetrain. ...

Tappet Adjuster is the adjustment screw used to set valve clearance in the cylinder head of Land Rover Series 4-cylinder engines. The screw thread...

Screw - a threaded fastener supplied as a single replacement screw.

Thrust Washer for the gearbox mainshaft, 0.128" thick. This is a selective-thickness thrust washer used to set mainshaft end-float during gearbox ...

Thrust Washer - Mainshaft - 0.130 Inch is a gearbox internal component positioned at the 3rd gear location on the mainshaft in the Series 1, Series...

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Tappet kit

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Bolt with a 3/8" UNF (Unified National Fine) thread and a 1-7/32" length. A standard imperial-thread fastener for chassis, driveline and body fixi...

Spring Shackle Distance Tube for the rear leaf spring shackle assembly. This spacer tube sets the correct spacing between the shackle plates, maint...

Accelerator pedal pad S3

Switch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...

Bush - Accelerator Linkage is a small bearing bush fitted to the accelerator linkage assembly on the 2.6L 6-cylinder petrol engine used in Series I...

Layshaft Gear - 1st Speed, part of the manual gearbox layshaft (cluster) gear train. Mounted on the layshaft, this gear meshes with the first-spee...

Inlet Valve Guide - a cylinder-head valve guide for the inlet valves of the 2.6L six-cylinder petrol (IOE) engine. Pressed into the cylinder head,...

Gearbox Top Cover Plate - the cover plate that closes the top aperture of the main gearbox casing. It seals the top of the gearbox over the select...

Gearbox Cover Plate Gasket for the LT76 gearbox. This rubber gasket seals the cover plate to the gearbox casing, sealing the joint against oil lea...

Cap Reservoir Br.m.cylinder

Clutch Slave Cylinder Repair Kit overhauls the clutch slave cylinder within the hydraulic clutch release circuit on the LT77 manual gearbox. The s...

Headlamp Bulb for the headlamp lighting circuit, rated for 24-volt electrical systems. This is a pre-focus type bulb: a locating flange on the cap...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Handbrake Expander operates the transmission-mounted drum handbrake, forcing the brake shoes apart against the drum when the handbrake is applied. ...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...

Spring plate

Locking plate

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Steering Box Side Plate Gasket seals the side cover plate against the casing of the manual steering box. It sits between the dowel-located side pl...

This brake drum is designed for long wheelbase Land Rover Series II and Series IIA vehicles. It is a drum brake component intended for use in tradi...

Choke Clip is the retaining clip that secures the choke cable at the Zenith carburettor. Part of the choke cable installation, it anchors the oute...

Exhaust Front Pipe for the 2.25L petrol engine, forming the first section of the exhaust system between the manifold and the intermediate pipe. It...

Exhaust Front Pipe in stainless steel, forming the first section of the exhaust system for the 2.25L petrol engine, between the manifold and the in...