Products

Rocker Cover Screw - Long for the Rover 3.5L V8 engine. This long 1/4" UNC x 1-5/16" screw secures the rocker cover to the cylinder head on the Ro...

Flame Trap fits into the crankcase ventilation circuit of the V8 twin-carburettor petrol engine, between the crankcase breather and the carburettor...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Union Nut for the fuel pipe in the fuel delivery system. This M12 union nut clamps a fuel pipe to its mating union or component port, drawing the ...

Distributor O-Ring, the sealing ring for the ignition distributor on the 3.5L V8 petrol engine. The O-ring seals the distributor base where it loc...

Valve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Drive Belt for the air conditioning compressor, part of the accessory belt drive on the 3.5L V8 petrol engine. The belt transfers drive from the c...

Head Gasket - 3.5L V8 - Metal is the cylinder head gasket for the 3.5L V8 petrol engine, sealing the joint between a cylinder head and the engine b...

Carburettor Grommet for the twin Stromberg carburettor installation on the V8 petrol engine. It sits in the air cleaner and carburettor air intake ...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Zenith Carburettor Overhaul Kit for the Zenith 36IV carburettor on 4-cylinder petrol engines. This is the complete overhaul kit for the Zenith 36I...

Engine Overhaul Gasket Set for the 2.6 litre IOE (inlet-over-exhaust) 6-cylinder petrol engine. A set of the gaskets and seals used when stripping...

Road Wheel Nut secures the road wheel to the hub. The nut clamps the wheel against the hub mounting face and must be tightened to the specified to...

Repair kit brake master cylinder

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Air Filter Element for the 3.5L V8 Twin Carb petrol engine air intake. This filter element is fitted in the air intake housing ahead of the carbur...

Distributor Cap for the 2.6 litre 6-cylinder IOE petrol engine, forming the top of the ignition distributor. The rotor arm sweeps inside the cap a...

Gasket kit carburettor Zenith Stromberg 175CD

parts catalogue SII & SIIa orginal (1968)

Carburettor Repair Kit for the six-cylinder petrol engine carburettor. It supplies the renewable service parts used to overhaul the carburettor and...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

H3 Halogen Bulb, 55W, single-filament. The H3 is a single-filament halogen capsule with a flying-lead connector, used in auxiliary lighting units ...

Round Mirror Head is the circular exterior mirror glass and housing that mounts on a wing- or fender-mounted mirror arm. It gives the driver a rea...

Brake Master Cylinder Repair Kit for the single-circuit master cylinder and servo system on the Series 2 and Series 3 Land Rover. This repair kit ...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Splined End

Constant Velocity (CV) Joint for the front axle, in the non-ABS configuration. It sits at the outer end of the front halfshaft, within the swivel h...

This taper roller bearing is designed for installation in the lower swivel pin housing, providing controlled rotational support and load distributi...

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston - Stainless Steel is a 41mm stainless steel piston that operates in the front brake caliper, part of the braking hydraul...

Bleed Screw for the imperial-specification front and rear brake calipers on the Range Rover Classic. This imperial-thread bleed screw fits the cal...

Split Pin used on a front-axle assembly to lock a castellated nut. The pin passes through the drilled fastener and the slots of the nut, and its le...