Products

Gearbox and transfer box lever set, forming the visible upper section of the gear change assembly. Machined alloy levers with a silver painted fini...

Terrafirma rear spring retaining plates 90/D1/RRC

Spring Retaining Plate - Rear for the rear coil spring seating assembly on Defender 110 and 130. Coil springs can become dislodged from their axle...

Radius Arm - front axle locating link in the coil-sprung front suspension. The radius arm ties the front axle to the chassis, controlling fore-and-...

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

Rear Spring Dislocation Cone - seats into the base of the rear coil spring mount and allows the spring to unseat (dislocate) cleanly at full axle d...

Shock Dropper - Rear - Pair: zinc-plated steel relocated rear shock absorber top mounts that lower the upper mounting point by 50mm. By relocating...

Twin Shock Mount Kit - Rear provides the additional mounting points required to run twin rear shock absorbers on each side of the rear axle. The ad...

Front twin shock mounting kit for the front damper mounting assembly, allowing two shock absorbers to be fitted per side - four dampers across the ...

Bump stop spacers, supplied as a pair, fitted between the chassis bump stop mounting and the bump stop itself. Each spacer packs the bump stop dow...

Front Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Rear Top Shock Mount Relocator - repositions the upper rear shock absorber mounting 50 mm (2 in) lower on the chassis. Dropping the top mount incr...

Top Shock Mount - upper shock absorber mounting for extreme long-travel suspension. This mount repositions the upper shock pickup point to accept ...

Long-Travel Spring Relocation Cone - replaces the standard coil spring seat so the spring can dislocate (drop out of its seat) at full axle droop a...

Rear Relocation Cones - Axle - Pair

Rear Relocation Cones - Axle - Pair

Front Shock Turret - Skeleton, +2 in - fabricated upper front shock mounting turret standing 50 mm (2 in) taller than the standard pressed turret. ...

Front coil spring retaining plates, supplied as a pair, forming part of the lower coil spring mounting at the axle. The plate clamps across the ba...

Front Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...

Rear Spring Spacer - +50 mm - locates between the rear coil spring and its upper seat to raise rear ride height by 50 mm. The spacer adds standing...

Steering Damper Relocation Kit enables the steering damper to be repositioned from the track rod to the drag link - the mounting position used on t...

Radius Arm - front axle locating link in the coil-sprung front suspension, tying the front axle to the chassis and controlling fore-and-aft axle lo...

Front radius arms with 3 degree caster correction, supplied as a pair. The radius arm is the longitudinal locating link between the front axle and ...

Creeper Joint Rear Radius Arms (PR) for 90/110/130/Discovery 1/RRC

Creeper Joint - For TF532

Skeleton Front Shock Absorber Turrets are the upper mounting towers for the front shock absorbers, bolting to the front chassis rails. The open tu...

Front shock absorber turrets, skeleton type, 30 mm extended, supplied as a pair. The turret carries the upper mounting eye of the front damper and ...

Coil spring trim spacers, 5 mm, fitted between the lower spring mounting plate and the axle to make fine ride height adjustments. Spacers are stac...

Front Shock Absorber Mounting Kit for long-travel monotube dampers, forming the upper turret and lower axle mounting points of the front suspension...

Rear Shock Mounting Kit - Mega Sport - the dedicated rear mounting system for Mega Sport rear shock absorbers, which use rose-joint mountings top a...

Hydraulic Bump Stop Mounting Kit - Front is the front-axle mounting hardware for a hydraulic bump stop installation, sitting within the suspension ...

Hydraulic Bump Stop Mounting Kit - Rear is the rear-axle mounting hardware for a hydraulic bump stop installation, sitting within the suspension bu...

Terrafirma hydraulic bump stop rear mounting kit 110/130 Needed when TF140 is going to build on the rear of the vehicle.

Smooth Body Shock Mount Kit

Intermediate Exhaust Pipe is a stainless steel replacement for the centre (intermediate) silencer section of the exhaust system. For the 2.5L 200Td...

External Rear Side Window Guards for the rear side window apertures, supplied as a pair and finished in black. The guards mount externally over th...

Rear Window and Quarter Light Guard Set protecting the rear door glass and the rear quarter lights, finished in black. The set comprises an intern...

Enhance the performance and fuel efficiency of your Land Rover Defender 90 (2.5 300Tdi Diesel, 1994-1997, up to TA) with this stainless steel exhau...

Upgrade the performance and fuel efficiency of your Land Rover Defender 90 (1997-1999, 2.5 300Tdi Diesel) with this stainless steel exhaust silence...

Intermediate Exhaust Pipe - stainless steel centre section of the exhaust system, fitted in place of the standard centre silencer between the front...

Centre Silencer Replacement Pipe for the exhaust system, fitted in place of the original centre silencer between the front and rear sections. The ...

X-Hinge Roof Tent - a hard-shell two-person roof tent for 4x4 and overland vehicles, mounted on roof bars or a roof rack. X-hinge opening system T...

Centre Silencer Replacement Pipe for the exhaust system, fitting in place of the intermediate (centre) silencer box. The pipe provides a straight-...

Rear Door Antenna and Work Light Mounts, supplied as a pair. The brackets locate in the gap alongside the rear door and provide a mounting point a...

Rear Side Window Storage Panels for the load space, supplied as a left- and right-hand pair. The panels fit against the rear side window area of t...

Centre Silencer Exhaust Pipe is the centre section of the exhaust system, incorporating the centre silencer, for the 3.9L V8 petrol application. I...