Products

Stud for use in Land Rover gearbox assembly.

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

Transfer Box Mainshaft is the central rotating shaft within the transfer box assembly, running through the gear train and transmitting drive betwee...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Starting Handle for manual cranking of the engine. The handle engages the dog on the front of the crankshaft, allowing the crankshaft to be turned...

Brake Shoe Spring for the drum brake assembly on Land Rover vehicles. This return spring pulls the brake shoes back from the drum face after each ...

Drive Shaft Hub Cap for the hub assembly on Land Rover Series vehicles. This cap fits at the outer face of the hub, closing off the drive shaft en...

Transfer Case Intermediate Gear with a 44/22 tooth configuration, operating within the transfer box gear train. The intermediate gear meshes with ...

Transfer Lever Knob in red, for the high/low range selector on the transfer gearbox. It threads onto the top of the transfer change lever and prov...

Inner Pinion Bearing for the Land Rover Series axle differential, supporting the pinion shaft at the inboard (crown wheel) end within the different...

Gear Lever Bracket - mounting bracket for the gear change lever on the LT76 gearbox. The gear lever pivots in the bracket, locating the lever over...

Gear Lever Housing The ball/socket housing for the main gear lever, mounted on the gearbox top cover (turret). It seats the spherical lower end of...

Gear Lever Retaining Plate for the gear lever turret on the LT76 manual gearbox. The plate bolts over the base of the gear lever to retain it in i...

Gear Lever Retaining Spring The spring that retains the main gear lever in its ball housing on the gearbox top cover. It bears down on the lever's...

Oil Seal - Clutch Withdrawal Sleeve for the Land Rover Series 2A gearbox, specifically the partially synchronised variant fitted with a sealed clut...

Circlip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...

Flexible Brake Hose - hydraulic hose carrying brake fluid from the rigid chassis or axle pipe to the wheel cylinder. Forms the flexible link acros...

Brake Rear Drum Cooper S & Mini 1984>

Washer for Land Rover applications.

Washer for the under-seat fuel tank front mounting assembly. This special-profile washer provides a secure bearing face at the front attachment po...

Locking Nut A locking nut for the gear lever plunger in the gearchange mechanism of the 5-speed manual gearbox. It retains the spring-loaded plung...

Gear Lever Anti-Rattle Plunger Spring The lower plunger spring for the gear lever in the gearchange mechanism of the 5-speed manual gearbox (LT77 a...

Four-Wheel Drive Selector Lever Bush for the transfer box gearchange linkage. The bush locates the four-wheel-drive selector lever at its pivot, t...

Joint Washer for the transfer gearbox top cover. This gasket seals the joint between the top cover and the transfer box housing, preventing oil le...

Core Plug - 1-3/8 in. diameter, threaded - for the Series engine block. This threaded plug seals a casting aperture in the engine block, retaining...

Woodruff Key - Camshaft Chainwheel for the 4-cylinder engine timing assembly. This Woodruff key locates the camshaft chainwheel on the camshaft no...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

Swivel Pin Seat Cone for the front axle swivel housing. This cone provides the precision seating surface on which the swivel pin locates within th...

Gearbox Reverse Stop Adjuster screw, part of the reverse gate mechanism in the manual gearbox gear-selection assembly. It sets and limits the gear...

Gearbox Reverse Stop Spring for the gear selector mechanism. The spring acts on the reverse stop plunger, providing the resistance the gear lever ...

Return Spring for Series hydraulic actuator and throttle control assemblies. This spring serves as a return spring in the hydraulic actuator assem...

Brake Lining Set for the rear drum brake assembly. This set contains the friction linings for both rear brake shoes, forming the braking surface b...

Drive Member Joint Washer - a sealing gasket fitted between the drive flange and the outer hub on Land Rover Series solid axles. This gasket seals...

Washer A copper joint sealing washer for the oil filter housing, part of the engine lubrication system. It seals the oil plug or the oil filter ad...

Mainshaft Thrust Washer for the Series I and Series II gearbox assembly. This 0.135 in (135 thou) washer controls the axial location of 3rd gear o...

Sealing Ring - Rocker Cover Breather Bolt for the 2.25-litre 4-cylinder engine. This sealing ring is fitted under the rocker cover breather bolt, ...

Copper Sealing Washer - a general-purpose copper crush washer used to seal threaded joints, plugs and unions. The soft copper deforms as the fitti...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

Washer used at multiple points within the manual gearbox assembly, including the main casing, extension housing, oil pump and speedometer drive hou...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Oil Cooler for the engine lubrication system, in 4-cylinder Military Lightweight specification. Connected into the engine oil circuit, it passes t...

Swivel Pin Housing Gasket for the front axle swivel assembly. This gasket seals the mating face between the chrome swivel ball housing and the fro...