Britpart Parts

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Cable Gaiter - Door Wiring is a protective sleeve and grommet fitted at the door aperture of the Defender body, routing the door wiring harness saf...

Horn Assembly for the audible warning circuit. This dual-tone unit pairs a high-tone and a low-tone horn on a common mounting bracket; the two soun...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Plain Washer - metric M8 plain washer for use in general fastening assemblies throughout the vehicle. A standard flat washer used to distribute lo...

Tow Bar Armature Kit is the towing subframe that mounts to the rear chassis assembly. The subframe bolts to the vehicle's rear chassis members and...

Propshaft Bearing for the rear propshaft carrier on the Range Rover L322 (2002-2009). This centre support bearing mounts to the vehicle body at th...

Air Conditioning Kit for retrofitting front air conditioning to TDCi Defenders that left the factory without it. Designed as an OE-style installat...

Bracket

Spare Wheel Cover Sticker - a self-adhesive vinyl decal for the rear-mounted spare wheel cover. Surface preparation determines how well it lasts: ...

Front Headlamp - Right-Hand - the complete headlamp unit for the right-hand side of the front lighting assembly, comprising the reflector, lens and...

Raised Air Intake - a steel snorkel that relocates the engine air intake from the inner wing up to roof-line height along the right-hand windscreen...

Front Spot Lamp Bar in nylon-coated steel, bolting to the front of the vehicle to carry auxiliary driving and spot lamps. The bar provides the mou...

Acrylic Front Lamp Guard Set for the headlamp units, supplied as a pair of clear acrylic protectors. Each guard clips over the headlamp without mo...

Locking Wheel Nut for alloy road wheels, a security nut fitted in place of one standard nut per wheel to deter theft. The head carries a coded spl...

Front Constant Velocity (CV) Joint for the front axle drive shaft. The CV joint transmits drive from the front axle to the road wheel while allowi...

Water Pump for the Rover V8 petrol engine, of the viscous-drive type. It mounts to the front of the engine and forms part of the engine cooling cir...

Exhaust Valve for the 2.6L 6-cylinder IOE (inlet-over-exhaust) petrol engine, forming part of the cylinder head and block valvetrain. The exhaust ...

Major Service Kit for the 3.6L TDV8 V8 turbo diesel engine, grouping the filters and drain plug required for a full engine service under a single p...

Major Service Kit for the 3.6L TDV8 V8 turbo diesel engine, grouping the filters and drain plug required for a full engine service under a single p...

Service Filter Kit for the 200 TDi 2.5L turbo diesel engine, grouping the filters and sealing washers required for a routine engine service under a...

Front Swivel Pin Kit is a complete overhaul kit for the front axle swivel housings, the steering pivot assembly that allows the front hubs to turn ...

Brake Pad Set for the rear disc brakes, supplied as an axle set together with a fitting kit. The brake pads are the friction elements that the cal...

kit front brake caliper guide pins

Special Nut - secures the rear knuckle to the lower and upper suspension arms. It retains the rear suspension arm bolts at the knuckle, holding th...

Headlamp Box is the pressed-steel mounting panel that forms the right-hand (offside) headlamp recess within the front wheelarch and valance assembl...

Spark Plug - ignites the air/fuel mixture in the combustion chamber of the petrol engine. It threads into the cylinder head with its electrode gap ...

Oil Filter for the engine lubrication system, suited to the 2.0L and 2.6L IOE (inlet-over-exhaust) petrol engines. The filter traps metallic parti...

Door Seal for the top of the door within the body weather-sealing system. The rubber seal fits along the upper edge of the door aperture, closing ...

Boost-Style Alloy Wheel, 16" x 7", finished in silver. A cast alloy road wheel of the Boost design pattern, suitable for on- and off-road use. Cen...

ACE High-Pressure Pipe - Rear Section within the Active Cornering Enhancement hydraulic circuit. This pipe forms the rear section of the high-pres...

External Roll Cage - a full external bolt-in roll cage that fits around the outside of the body to provide rollover protection. It is a 6-point bo...

Rear Fog Lamp with LED illumination, forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibili...

Ignition Switch - Diesel - Switch Only is the electrical switch element of the ignition system for diesel applications. It supplies the rotary swi...

jet assy

Auxiliary Drive Belt for the 1.8L K-Series four-cylinder petrol engine, in air-conditioned applications. The belt drives the alternator from the c...

Auxiliary Drive Pulley for the accessory drive belt system of the 4.4L V8 M62 B44 DOHC petrol engine. The pulley guides the polyvee auxiliary belt...

Intercooler Hose for the charge-air (boost) circuit, incorporating a provision for the charge-air sensor. It conveys pressurised charge air throug...

Restore optimal engine performance with this Air Cleaner Hose Kit, specifically designed for the Land Rover Freelander 1 with a K-Series petrol eng...

Coolant Hose - Thermostat To Water Pump - V8

Coolant Hose for the fuel cooler return line. This hose returns coolant from the fuel cooler back to the engine cooling circuit, carrying off the ...

Bleed Hose is a small-bore coolant hose within the expansion tank and hose assembly of the engine cooling system. It vents air from the high point...

Radiator Mount is a moulded rubber isolator in the engine cooling system, forming part of the radiator mounting. It locates the radiator within it...

Power Steering Pipe - the return line in the power steering hydraulic circuit. It carries low-pressure fluid from the steering box back to the pow...

Pipe Clamp for the engine oil cooler pipe circuit. This clamp plate secures the oil cooler pipes in the engine bay, restraining them against vibra...

Left-Hand Exhaust Downpipe for the 3.5L V8 EFI engine, non-catalyst exhaust configuration. Connects the left cylinder bank exhaust manifold outlet ...

Rear Silencer & Tailpipe - Stainless - the rear section of the exhaust system, combining the rear silencer and tailpipe in a single assembly, c...

Clutch Pipe is the upper rigid section of the clutch hydraulic circuit, for left-hand-drive configuration. The pipe carries hydraulic fluid from t...