for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Decoke Gasket Set for the 3.9/4.0/4.2L Rover V8 EFI petrol engine. This is the set of gaskets and seals used to reseal the top end of the engine - ...
View full detailsClutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...
View full detailsOil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...
View full detailsFront Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...
View full detailsBelt
Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...
View full detailsStop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...
View full detailsCoolant Expansion Tank in black, part of the engine cooling system. The tank serves as the system's pressurised reservoir and fill point, accommod...
View full detailsCam Cover Sealing Washer Seals a camshaft cover retaining bolt on the 300 TDi 2.5L turbo diesel engine. Fitted beneath the head of the cam (rocker...
View full detailsFront Half Shaft for the left-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant velo...
View full detailsMainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...
View full detailsTappet Adjusting Screw for the 2.5L 300 TDi turbocharged diesel engine, fitted in the rocker arm of the valvetrain. Threaded into the rocker arm t...
View full detailsDrive Belt is the auxiliary drive belt for the 3.5L V8 petrol engine. Running from the crankshaft pulley, it drives the alternator and, where fitt...
View full detailsAir Flow Sensor for the V8 EFI petrol engine management system, mounted in the intake tract between the air filter and the throttle. Measures the ...
View full detailsABS Wheel Speed Sensor - front sensor for the four-wheel anti-lock braking system. The sensor mounts in the front axle housing with its pole piece...
View full detailsSplit Pin, a Genuine Land Rover steel cotter pin that locks a clevis pin or pinned linkage joint in place. The two legs go through the cross-drille...
View full detailsFuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...
View full detailsSteering Lever - RHD for the Adwest power steering box, supplied with the ball joint fitted. Also known as the drop arm, the lever clamps onto the...
View full detailsDifferential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...
View full detailsValve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...
View full detailsFuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...
View full detailsBrake Disc Splash Shield - Front, RH, mounted behind the right-hand front brake disc. The shield sits between the stub axle / hub and the brake di...
View full detailsStepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...
View full detailsTaper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...
View full detailsThermostat Kit for Electric Fan Kenlowe
Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...
View full detailsFront Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...
View full detailsOil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...
View full detailsTransfer Box - LT230 43D is a reconditioned two-speed transfer gearbox with a 1.4:1 high-range ratio. The transfer box mounts to the rear of the m...
View full detailsValve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...
View full detailsSet - 200 TDi Head Including Bolts
Panhard Rod Bush Set for the front suspension lateral location assembly. Each bush in this set is pressed into the Panhard rod eye and provides th...
View full detailsClutch Plate
Exhaust Manifold Locking Washer that secures the exhaust manifold fixings to the cylinder head. The tab washer fits under the manifold bolt or nut...
View full detailsWheel Nut for alloy wheel fitment on Defender, Discovery 1 and Range Rover Classic. This tapered-seat wheel nut is designed for use with alloy whe...
View full detailsMain Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...
View full detailsPipe Clip, a routing clip that retains pipework and small-bore lines against the chassis, body or transmission casing. It supports breather, fuel,...
View full detailsBow Shackle Bow-shaped recovery shackle with a threaded pin, used to connect a recovery strap or rope to a recovery point on a winch bumper. The w...
View full detailsTiming Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...
View full detailsFront Crankshaft Oil Seal for the 2.5L 300TDi turbo diesel engine. It fits around the crankshaft nose at the front of the engine, sealing the point...
View full detailsThermostat for the 2.5L 200TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. This thermostat opens at ...
View full detailsThermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...
View full detailsTransmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...
View full detailsCamshaft Retaining Plate for the four-cylinder engine. Bolted to the front face of the cylinder block behind the camshaft gear, it locates the cams...
View full detailsFront Crankshaft Oil Seal for the 2.5L 300TDi turbo diesel engine. It fits around the crankshaft nose at the front of the engine, sealing the point...
View full detailsFlywheel Assembly for the manual transmission on the 2.5L 200 TDi and 300 TDi turbo diesel engines. Bolted to the rear of the crankshaft, the flyw...
View full detailsElbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...
View full detailsBrake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →