for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Heater Blower Assembly Seal - sealing element within the heater and blower assembly of the heating and ventilation system. It closes the joint bet...
View full detailsHeater Blower Assembly Seal - sealing element within the heater and blower assembly of the heating and ventilation system. It closes the joint bet...
View full detailsHeater Blower Assembly Seal - sealing element fitted to the heater blower assembly within the HVAC intake housing. It seals the joint between the ...
View full detailsA/C Compressor O-Ring seals a refrigerant line union at the air conditioning compressor. The O-ring is clamped between the pipe end fitting and th...
View full detailsA/C Pipe - Condenser to Receiver Dryer forms part of the air conditioning refrigerant circuit, carrying refrigerant from the condenser outlet to th...
View full detailsO-Ring - a sealing O-ring for the air conditioning evaporator assembly and hose connections, in configurations other than the V8 EFi petrol. It se...
View full detailsA/C Switch - facia-mounted switch for the air conditioning system. Fitted in the heater and ventilation control panel of the centre facia, it is t...
View full detailsGear Lever is the main gear selector lever for the manual transmission. The driver moves it through the gate to select gears via the gearchange li...
View full detailsValve Spring - V8 is a cylinder head valve spring for the Rover 3.5L and 3.9L V8 petrol engine. The valve spring seats between the cylinder head a...
View full detailsDoor Latch Sill Button for the door locking mechanism, finished in black. It fits at the door sill and connects to the latch, providing the manual ...
View full detailsGrab Handle for the interior roof trim, mounted to the body structure above the door aperture. The handle fastens through the headlining into the ...
View full detailsExhaust Heat Shield - a formed metal shield fitted in the exhaust system area of the underbody. The shield sits between the exhaust and the adjace...
View full detailsKey - Mainshaft
Hose - Heater Water
Hose - Heater Water
Fuel Filter Shield is a protective cover fitted over the fuel filter assembly. It mounts over the filter housing and shields the filter body and i...
View full detailsWasher for the bonnet insulation pad. This washer retains the sound- and heat-insulation pad against the underside of the bonnet, holding the pad ...
View full detailsBody Washer, 22mm outer diameter, 6.5mm inner diameter. A flat washer that spreads the clamping load of a fixing across the mounting surface, prot...
View full detailsLocating Dowel for the Rover V8 petrol engine. The dowel positions mating components accurately during assembly, ensuring correct alignment before...
View full detailsInlet Air Seal for the Solex carburettor connection on the 2.25L 4-cylinder petrol induction system. Seals the joint between the air intake and th...
View full detailsVent Assembly Knob for the dashboard air vent control on models without air conditioning. The knob fits onto the vent control lever and provides t...
View full detailsBolt Mounting bolt for the power steering pump and front cover housing, and for air conditioning compressor and condenser mountings.
Bolt Flanged-head bolt used as a fastener in Land Rover assemblies.
Gear Change Lever Knob for the transfer box gear change lever. The knob fits to the top of the transfer lever and forms the hand grip used to sele...
View full detailsCylinder Head & Sump Bolt Bolt used on the cylinder head and sump of the 2.5L Td5 five-cylinder turbo diesel engine.
Fuse Holder Assembly - a foam block that retains spare blade fuses, forming part of the fuse box arrangement in the body electrical system. It moun...
View full detailsTransfer Box Gear Knob in aluminium, fitted to the high/low range selector lever of the LT230 transfer box. The knob threads onto the top of the t...
View full detailsHandbrake Shoe Kit - the retention (hold-down) hardware for the transmission handbrake, which acts on the LT230 transfer box rather than at the roa...
View full detailsScrew - a threaded fastener used across several exterior body fixings. It secures fittings within the radiator grille, the rear end door seals and...
View full detailsDoor Opening Weatherstrip - the rubber seal that runs around the rear side door aperture. It closes the gap between the door and the body opening t...
View full detailsDoor Opening Weatherstrip - the rubber seal that runs around the rear side door aperture. It closes the gap between the door and the body opening t...
View full detailsExhaust Gas Temperature Sensor for the post-catalyst position in the exhaust after-treatment system of the 2.2L Puma TDCi diesel engine. Installed...
View full detailsExhaust Gas Temperature Sensor for the pre-catalyst position in the exhaust after-treatment system of the 2.2L Puma TDCi diesel engine. Installed ...
View full detailsResistor Assembly sets the blower motor fan speeds within the heating and air conditioning system. Wired in series with the blower motor on the lo...
View full detailsSteering Ignition Lock Housing - the housing that mounts the ignition switch and steering-column lock to the upper steering column. It locates the...
View full detailsExhaust Gas Temperature Sensor for the diesel particulate filter position in the exhaust after-treatment system of the 2.2L Puma TDCi diesel engine...
View full detailsDrive Belt Tensioner Pulley for the auxiliary drive belt system on the 2.2/2.4L TDCi diesel engine. The pulley runs against the auxiliary (poly-V)...
View full detailsRear Loadspace Rubber Mat for the rear load area. Moulded rubber mat shaped to the rear loadspace floor, protecting it against dirt, moisture and ...
View full detailsRadiator Fan Shroud - the lower section of the cooling fan housing, fitted behind the radiator around the bottom of the engine-driven cooling fan. ...
View full detailsFloor Mat Set - carpet contour mats that lie over the fitted floor covering, shaped to follow the footwell contours so they sit flat and stay in po...
View full detailsNut - an M8 x 1.25 captive U-spring nut used to mount the air suspension compressor. The spring-steel body clips over the chassis bracket to provi...
View full detailsLock Set - Complete Vehicle is a matched set of lock barrels for the vehicle security and locking system. It comprises a steering column (ignition...
View full detailsHandbrake Operating Lever from the parking brake control assembly. The lever is the driver-operated arm that applies the transmission brake through...
View full detailsEngine Oil Pan (sump) for the 2.4L and 2.2L Duratorq TDCi diesel engine - Engine Block and Lubrication assembly group. Bolts to the underside of t...
View full detailsFront Shock Absorber - hydraulic damper for the front suspension, supplied with its mounting hardware. The damper controls the rate at which the f...
View full detailsExhaust Box Assembly forming the rear silencer section of the exhaust system on 2.5L 4-cylinder 300 TDi diesel applications. The box attenuates ex...
View full detailsSeat Belt
Camshaft Position Sensor for the 2.2L turbo-diesel engine. The sensor monitors the position of the camshaft and signals the engine control unit, w...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →