for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Brake Pedal Assembly for the pedal box. The pedal pivots on its mounting in the pedal box and transmits driver input to the brake master cylinder p...
View full detailsPinion Shaft is the input (primary pinion) shaft of the R380 five-speed manual gearbox. It carries drive from the clutch into the gearbox and mesh...
View full detailsAir Cleaner Lid - the upper cover of the air cleaner assembly in the induction system, clamping over the filter element and sealing the filter hous...
View full detailsAlternator Bracket mounts the alternator to the engine, locating it within the accessory drive so the drive belt runs in correct alignment with the...
View full detailsHex Nut - M12 - a standard M12 hexagonal nut used as a general-purpose fastener across the vehicle. The six-sided form is tightened with a standar...
View full detailsDrive Flange for the MT82 six-speed manual gearbox, mounted at the transmission output. It transmits drive from the gearbox output to the propelle...
View full detailsintegral bumper and nudge bar .BA 009 BB2013
Accelerator Pedal Potentiometer, part of the accelerator pedal assembly in the electronic throttle (drive-by-wire) control system. It converts ped...
View full detailsRetainer
hose ANR5782
Retainer
Transmission Tunnel Cover - a moulded rubber cover that fits over the transmission tunnel in the front floor, between the driver and passenger foot...
View full detailsPlate
Dash Insulation Pad for the dashboard (fascia) assembly. The pad mounts behind the dash trim to reduce heat and noise transfer into the cabin from...
View full detailsLamp
EGR Valve - Puma TDCi is the exhaust gas recirculation valve for the 2.4L Duratorq-TDCi (Puma) diesel engine. The valve meters a portion of exhaus...
View full detailsMain Bearing Cap Bolt for the cylinder block bottom end, clamping a main bearing cap to the block and retaining the crankshaft main bearing shells....
View full detailsInstrument Finisher for the left-hand side of the facia (dashboard) instrument panel. The finisher frames and trims the instrument area, retaining...
View full detailsFuel Tank Level Sender fitted inside the fuel tank as part of the fuel delivery assembly. The sender uses a float-driven variable resistance to si...
View full detailsDash Trim Finisher for the dashboard (fascia) assembly. The finisher retains and covers the edge of the dash trim, securing the panel and giving a...
View full detailspipe NTC1685
Accelerator Pedal Potentiometer is the pedal position sensor within the electronic engine management system, converting accelerator pedal travel in...
View full detailsFuel Block Connector - fuel block and pressure regulator assembly in the fuel supply and return circuit of the Td5 2.5L 5-cylinder turbo diesel. I...
View full detailsWiring assy YMD111080
Fuel Block Connector - the connector assembly that mounts to the fuel block at the rear of the engine, within the fuel injector, pipe and filter as...
View full detailsFinger Pull for the door-top sliding glass window. Attaches to the sliding glass pane, providing a grip to slide the window open and closed.
Cover - Spare Wheel
Rear Door Trim Panel is the interior casing that finishes the inside face of the rear tail door, concealing the door structure behind a moulded pan...
View full detailsFront Wheelarch - outer wheelarch and eyebrow panel forming part of the front bodyside assembly. The wheelarch bolts to the front wing panel and c...
View full detailsHeater Control - the heater and air-conditioning control panel mounted in the centre of the dashboard. It carries the rotary controls for cabin te...
View full detailsMass Air Flow Sensor measures the mass of air drawn into the engine and reports it to the engine control module for fuel metering. It mounts in th...
View full detailsRemote Control - Alarm & Central Locking
Inlet Manifold - 2.2L TD4 (224DT) diesel engine, air intake and charge air assembly. The manifold receives charge air from the intercooler outlet ...
View full detailsSpare Wheel Carrier - a swing-away rear carrier that takes the spare wheel off the rear door and transfers its weight into the body structure, reli...
View full detailsGear Change Cross-Shaft within the gearbox remote and selector linkage. The cross-shaft transfers the movement of the gear lever through the remot...
View full detailsScrew - M4 x 16mm metric machine screw used as a general fixing. A multi-application fastener rather than a component-specific part; the same scre...
View full detailsLatch Assembly for the tunnel console (cubby box) lid. The latch holds the cubby box lid closed and releases it when operated, mounting to the lid...
View full detailsClip
Air Cleaner Retaining Clip for the air filter housing, securing the housing cover to its body. The clip clamps the air cleaner lid closed so the f...
View full detailsInstrument Finisher for the right-hand side of the facia (dashboard) instrument panel. The finisher frames and trims the instrument area, retainin...
View full detailsFront ABS wheel speed sensor, part of the four-wheel anti-lock braking system's sensing circuit. Catalogued under a sensor kit part number; the ass...
View full detailsOil Filter Adaptor for the 2.2 Td4 diesel engine, part of the oil filter assembly. The adaptor bolts to the cylinder block and provides the mounti...
View full detailsIn-Tank Fuel Pump mounted within the fuel tank as part of the fuel delivery system. It draws fuel from the tank and supplies it under pressure to ...
View full detailsEGR Valve for the exhaust gas recirculation system. The valve meters a controlled portion of exhaust gas back into the intake tract to lower peak c...
View full detailsCooling Fan for the 2.2L Puma TDCi diesel engine - a viscous coupling with an integral fan blade that mounts on the water pump drive. The temperat...
View full detailsOil Cooler - a transmission oil cooler forming part of the gearbox cooling circuit. Transmission fluid is routed through a finned matrix so that he...
View full detailsSwivel Pin Housing, left-hand side - the ball housing that forms the outer end of the front axle and carries the steering swivel. It is located on...
View full detailsAir Conditioning Condenser - heat exchanger in the air conditioning refrigerant circuit, mounted ahead of the engine cooling radiator in the front ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →