for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Brake Pedal Assembly mounted in the pedal box of the braking system. The assembly transmits driver pedal effort to the brake servo pushrod, pivoti...
View full detailsClutch Repair Kit
Brake master cylinder for vehicles fitted with the four-wheel anti-lock braking system. It sits in the brake hydraulic circuit between the brake se...
View full detailsWindscreen laminated front windscreen glass. Clear (non-tinted) glass without an integral heating element (non-heated).
1st Speed Gear for the LT95 four-speed gearbox, forming part of the mainshaft constant-mesh gear cluster. It meshes with its corresponding layshaf...
View full detailsDoor Lock and Alarm Module - the electronic control module that governs the vehicle's Central Door Locking (CDL) and anti-theft alarm functions. I...
View full detailsAir Cleaner Assembly is the intake air filter housing that supplies clean air to the engine's induction system. It draws air through the inlet duc...
View full detailsRear Output Shaft is the driven shaft at the rear of the LT230 transfer box, transmitting drive from the transfer gearbox to the rear propeller sha...
View full detailsEGR Cooler for the exhaust gas recirculation system. It uses engine coolant to lower the temperature of recirculated exhaust gas before it re-enter...
View full detailsAxle Stub Shaft – Rear Outer is the outer half shaft of the rear axle assembly, transmitting drive from the differential through the axle casing to...
View full detailsCamshaft Cover for the Puma 2.4L TDCi diesel engine. This cover encloses the top of the cylinder head, housing and protecting the camshaft and valv...
View full detailsFront Seat Belt Anchor Bracket forming the anchorage for the front seat harness. It provides the mounting point to which the front seat belt is sec...
View full detailsSliding Roof Glass - the tinted glass panel for a tilt-and-slide sunroof, forming the moving light that closes and opens the roof aperture. The pa...
View full detailsInstrument Panel Moulding for the dashboard, in left-hand-drive configuration. A moulded trim component that forms part of the instrument panel, f...
View full detailsSeat Frame - front seat base frame for the left-hand seat. The frame forms the structural base of the front seat, carrying the seat cushion and pr...
View full detailsFront Protection Bar - an A-frame nudge bar for the front exterior protection assembly. The bar is a single-piece construction with a textured bla...
View full detailsSpeedometer for the instrument pack, calibrated to Japan-market specification for the 4.0L V8 EFi petrol engine with automatic transmission. Mount...
View full detailsRear Lower Wheelarch is a body panel forming the lower section of the rear wheelarch on the 110" wheelbase Station Wagon bodyshell. It defines the ...
View full detailsSteering Box for the power-assisted recirculating-ball steering system. It converts rotational input from the steering column into lateral movement...
View full detailsThrottle Body - EGR Intake is the intake throttle valve serving the exhaust gas recirculation (EGR) system on the diesel engine. It meters intake ...
View full detailsHeater
Air Conditioning Compressor is the driven pump of the air conditioning refrigerant circuit, drawing low-pressure refrigerant vapour from the evapor...
View full detailsFront Bulkhead - the structural body panel separating the engine compartment from the cabin, providing mounting for the fascia, pedal box and winds...
View full detailsCoolant Vent Hose - a small-bore hose in the engine cooling and cabin heater circuit of the 2.4 TDCi Puma diesel. Connected at the heater outlet, ...
View full detailsQuarter Light is the rear quarter window glass for the left-hand (LH) side. The glass fits the fixed rear quarter aperture in the body side behind...
View full detailsFront Roof Capping - RH - external capping section fitted along the right-hand front edge of the roof, covering the joint between the roof panel an...
View full detailsAir Duct for the heater assembly cold-air intake, left-hand-drive diesel applications. Channels fresh air from the intake aperture into the heater...
View full detailsFront Axle Differential Casing for the front drive axle. This casting forms the central housing of the front axle. It carries the differential cro...
View full detailsRear Body Capping Corner, a body trim finisher fitted to the top edge of the rear body. This corner section caps the exposed top edge of the body ...
View full detailsRadiator Hose Clip secures a coolant hose within the engine cooling system, clamping the hose onto its radiator or engine connection to maintain a ...
View full detailsFacia Louvre Vent Housing - a dashboard air outlet housing within the heating and ventilation (HVAC) system. The housing carries the adjustable lo...
View full detailsAdhesive Pad is a self-adhesive mounting pad used to bond and locate a small component against a body panel or bracket. It provides a clean fixing...
View full detailsRadius Arm Bush is the compliant mounting bush at the radius arm pivot in the front suspension. The radius arm locates the front axle fore-and-aft...
View full detailsHeater To Bulkhead Seal seals the joint between the heater and blower duct and the bulkhead aperture, within the heating and ventilation assembly. ...
View full detailsWasher
Cover Assembly
Rear Side Door Seal for the right-hand rear side door. It seals the perimeter of the door aperture against the body frame, keeping out water, dust ...
View full detailsVacuum Pump Oil Drain Pipe for the vacuum pump lubrication circuit on the Td5 2.5L 5-cylinder turbo diesel. The Td5 vacuum pump is lubricated by p...
View full detailsDistributor Repair Kit
Touch-Up Paint Pencil applies the Epsom Green body colour to small stone chips and scratches in the paintwork. The pencil applicator gives accurat...
View full detailsWiring Connector for the chassis wiring harness, used in the fuel tank circuitry. The connector forms a serviceable electrical junction between ha...
View full detailsCylinder Head Kit
mat BTR1194LOY
Blanking Plug used to close off an unused aperture in the body or panel work, part of the grommets and blanking group. It seals a redundant or opt...
View full detailsBlanking Plate - moulded plug that closes an unused switch aperture in the facia or switch console. Where a vehicle is built without an optional s...
View full detailsLayshaft Roll Pin for the manual transmission. This roll (tension) pin locates and retains the layshaft within the gearbox casing, holding the sha...
View full detailsRelay for the 24V electrical system used on military 'Wolf' specification vehicles. A relay switches a high-current circuit using a low-current co...
View full detailsPiston Assembly for the 3.5-litre Rover V8 petrol engine, supplied at 0.020" oversize for a rebored cylinder block. It locates in the cylinder bore...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →