for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Spring Washer - Side Repeater Lamp A spring washer used at the side repeater lamp mounting. Fitted beneath the securing nut or screw, it maintains...
View full detailsSnap Ring - a retaining ring for the rear suspension top link ball joint. The snap ring seats in a groove to secure the ball joint within the top ...
View full detailsThrust Washer for the reverse idler gear in the LT95 four-speed gearbox. It bears against the reverse idler gear on its shaft, setting the gear's ...
View full detailsCarburettor Float Needle is the needle valve that regulates fuel entry into the carburettor float chamber. Actuated by the float, it seats to shut...
View full detailsSnorkel Retaining Clip for the raised air intake assembly. The clip secures the raised air intake (snorkel) to the body, holding the intake duct f...
View full detailsFuel Pipe - Accumulator to Filter is a rigid fuel line in the fuel supply circuit, carrying fuel from the accumulator to the fuel filter on the fee...
View full detailsDoor Splash Seal is a water shedder fitted to the inner face of the front door, behind the trim panel. It forms a moisture barrier that directs wa...
View full detailsOil Catcher - an internal lubrication component of the 5-speed manual gearbox. The oil catcher collects lubricant thrown off by the rotating gears...
View full detailsRear Wiper Motor Cover trim cover for the rear screen (backlight) wiper motor mounted on the tailgate, finished in Palomino. Fits over the wiper m...
View full detailsStud for the timing cover (front cover) of the 2.5L 4-cylinder diesel engine. The stud locates and clamps the front cover to the cylinder block, p...
View full detailsAnti-Squeak Pad for the undertray assembly. This acoustic, sound-deadening pad is fitted between the undertray panel and its adjacent mounting surf...
View full detailsGear Lever Gaiter Retainer - trim component within the centre console and gear lever assembly that secures the gear lever gaiter to the console. T...
View full detailsCOVER - INSULATOR
Heater Hose - Return - the coolant return hose of the heater circuit, for the 2.5L 200 TDi diesel engine. It carries coolant from the heater matri...
View full detailsSide Member is a structural body member forming part of the rear seat mounting structure, providing the anchorage for the inward-facing rear seats....
View full detailsSide Member is a structural body member forming part of the rear seat mounting structure, providing the anchorage for the inward-facing rear seats....
View full detailsNut Plate providing the threaded anchorage for the rear inward-facing seats. The plate carries captive threads and mounts behind the body panel, g...
View full detailsTailgate Seal, rubber weatherseal for the rear tailgate. It fits around the tailboard aperture, sealing the joint between the closed tailgate and ...
View full detailsMonobolt Rivet - 1/4" structural blind rivet for body and chassis fastening. The Monobolt is a high-strength blind rivet set from one side of the ...
View full detailsHex Nut A 3/8 UNF hexagonal fastener used in the carburettor assembly of the 3.5L V8 petrol twin-carburettor engine. It secures components within ...
View full detailsAdjusting Link for the power steering pump mounting, used to set and hold drive belt tension. The link connects the pump body to a fixed bracket a...
View full detailsDifferential Pinion for the Land Rover-type axle differential. The pinion gear runs on the differential cross-shaft inside the diff carrier, meshi...
View full detailsLayshaft Shim for the LT95 4-speed gearbox. The shim sets the endfloat of the layshaft (countershaft) within the LT95 gearbox casing, fixing its a...
View full detailsLayshaft Shim for the LT95 4-speed gearbox. The shim sets the endfloat of the layshaft (countershaft) within the LT95 gearbox casing, fixing its a...
View full detailsLayshaft Shim for the LT95 4-speed gearbox. The shim sets the endfloat of the layshaft (countershaft) within the LT95 gearbox casing, fixing its a...
View full detailsBlanking Plug for sealing an unused panel aperture. This 20.5mm plastic plug closes off an open hole in the body or chassis panelwork, keeping out...
View full detailsRetainer for the floor rubber mat sections. This right-hand retainer secures the intermediate and rear floor rubber mat sections, clamping the mat...
View full detailsSeat Catch for the rear seat mounting. This locking catch secures the rear seat in its mounted position, engaging to hold the seat down and releas...
View full detailsBolt - UNF - Tail Light is a Unified National Fine (UNF) fastener used in the rear lamp assembly on Defender models built up to VIN LA939975. This...
View full detailsBody Mount Filler is a packing piece used at the body-to-chassis mounting points on the High Capacity Pick Up (HCPU) and Crew Cab body configuratio...
View full detailsValve Stem Oil Seal seats on the valve guide within the cylinder head valvetrain, sealing the point where the valve stem passes through the guide. ...
View full detailsFlanged Bolt is an M12 x 40 mm fastener with an integral flanged head that distributes clamping load across the joint without a separate washer. U...
View full detailsTow Equipment Bolt is an M10 x 115 mm fastener used to mount rear towing equipment, such as a drop plate with tow ball or a rear towing step, to th...
View full detailsChassis Frame Washer is a load-spreading washer used in the chassis frame fastening assembly. It seats under a bolt head or nut to distribute clamp...
View full detailsDifferential Bearing Shim for the axle differential assembly. The shim fits behind a differential carrier bearing in the axle casing. It sets the ...
View full detailsOil Feed Pipe - 2.5L Turbo Diesel carries pressurised engine oil to the turbocharger on the 2.5L 4-cylinder turbo diesel engine (early 19J, non-TDi...
View full detailsEGR Valve Filter is a service component of the exhaust gas recirculation (EGR) system, fitted in line with the EGR solenoid control valve. It filt...
View full detailsBrake Pipe Clip secures and routes rigid brake pipe runs within the braking system, holding the pipe against the chassis or body to maintain its ro...
View full detailsRivet - a blind body and trim fastener used throughout the vehicle's panel and bracket fixing points. It forms a permanent riveted joint where pan...
View full detailsA/C Evaporator Seal seals the evaporator assembly within the air conditioning system's HVAC housing. Fitted at the evaporator core interface to pr...
View full detailsHose Clip for the cooling system, securing coolant and heater hose connections. This clip clamps a hose onto its pipe or stub, holding the joint t...
View full detailsAir Cleaner Mounting Rubber for the engine air intake system. This flexible rubber mount locates and supports the air cleaner (air filter) housing...
View full detailsFuse Box Decal is the printed identification label for the fuse box, showing the fuse positions and their circuit ratings. It mounts on the fuse bo...
View full detailsCoolant Pulley for the engine cooling circuit of the V8 EFI petrol engine. The pulley bolts to the coolant pump drive flange and is driven by the ...
View full detailsReservoir Bracket mounts and supports the power steering fluid reservoir. It holds the reservoir in position within the power steering circuit, lo...
View full detailsAir Flow Restrictor for the 3.5L V8 twin-carburettor intake. Fitted in the carburettor air intake to meter incoming air flow, working alongside th...
View full detailsExhaust Hanger Bracket supports the exhaust system, locating a section of the pipe or silencer to the vehicle underbody. The bracket provides the ...
View full detailsFuel Tank Bracket mounts and supports the auxiliary fuel tank, securing it to the chassis and locating it against the underbody.
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →