for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Rear Lamp Panel Cover - left-hand (LH) rear body panel that forms the surround and mounting face for the rear lamp cluster. It fits to the rear co...
View full detailsRear Lamp Panel Cover - right-hand (RH) rear body panel that forms the surround and mounting face for the rear lamp cluster. It fits to the rear c...
View full detailsTie Down Hook check strap bracket for the rear swing gate, part of the gate hardware. Anchors the gate check strap, retaining the swing gate and l...
View full detailsSelf Levelling Unit Retaining Strap secures the rear self-levelling suspension unit to its mounting, holding the unit in position and restraining i...
View full detailsRear Seat Bracket inner mounting bracket for the rear seating, securing a forward-facing individual rear seat to the floor. Locates the inner side...
View full detailsRear Seat Clip - a retaining clip in the rear seat assembly, used to secure the seat frame to its mounting. Works alongside the rear seat frame an...
View full detailsBlanking Plug closes off an unused aperture in the front bumper and chassis under-ride protection bar. Pushed into an open hole to seal it, the pl...
View full detailsOuter Finisher - an external trim finisher fitted to the bodyside, used on the rear cab body panel and around the sliding side windows of the hard ...
View full detailsSelf Levelling Unit Gaiter - Upper is the protective rubber boot fitted over the upper ball joint of the rear self-levelling suspension unit. It s...
View full detailsHandbook - English Edition
Instrument Panel is the moulded facia structure forming the dashboard, carrying the instrument binnacle, switch panel and heater control assembly a...
View full detailsAccelerator Pedal Mounting Bracket supports the accelerator pedal assembly within the throttle control system. It mounts the pedal to the bulkhead...
View full detailsInstrument Panel is the moulded facia structure forming the dashboard, carrying the instrument binnacle, switch panel and heater control assembly a...
View full detailsRear Subframe Angle Bracket for the rear chassis and subframe assembly. The angled bracket provides a mounting and reinforcement point at the rear...
View full detailsDoor Latch Mechanism Spacer for the rear end door latching assembly. It sets the correct standoff between the latch mechanism and its mounting fac...
View full detailsWheelguard - a protective guard fitted in the wheel arch area of the body. It shields the surrounding bodywork and underbody components from mud, ...
View full detailsCylinder Head Gasket for the 300TDi 2.5L four-cylinder turbo diesel engine, sealing the joint between the cylinder head and the engine block. It s...
View full detailsOil Pump Suction Pipe is part of the engine lubrication system on the Td5 2.5-litre five-cylinder turbo diesel. It forms the pick-up line that dra...
View full detailsAlternator Banjo Bolt is the hollow union bolt that secures the oil feed line to the vacuum pump on the alternator of the Td5 2.5L 5-cylinder turbo...
View full detailsPulley
Alternator Fan for the alternator within the engine charging circuit, for applications built without air conditioning. The fan fits to the drive e...
View full detailsBrake Pipe Bracket secures and routes the rigid brake pipe within the front braking hydraulic circuit. It clamps the brake pipe to the chassis to ...
View full detailsAlternator for the 3.5L V8 petrol engine - Lucas A133 type, rated at 65A. The alternator sits in the engine's charging circuit, driven by the auxi...
View full detailsThrottle Cam
Pipe assembly brake
Screw, 1/4" UNF x 3/8" hex-head set screw, a general-purpose threaded fastener used at multiple points across the vehicle.
Screw used as a threaded fastener within the fuel system and throttle assembly of the 3.5L V8 twin-carburettor petrol engine.
Brake Pipe Assembly for the front brake hydraulic circuit on vehicles equipped with four-wheel ABS. The rigid pipe carries pressurised brake fluid...
View full detailsScrew
Tailboard Screw securing the lower side-hinged tailboard at the rear of the body. It fixes the tailboard panel to its hinge and surrounding mountings.
Diode used in the vehicle's electrical system. A diode conducts current in one direction only. In the wiring it is used to protect circuits and to...
View full detailsFuel Vapour Separator for the fuel supply line on carburettor petrol applications. The separator sits in the fuel line and divides fuel vapour fro...
View full detailsHandbrake Lever Plate is a component of the parking brake lever assembly mounted in the cab. It forms part of the hand-operated lever mechanism th...
View full detailsWoodruff Key for the injection pump drive on the 2.5L 4-cylinder diesel engine (naturally aspirated and turbo). The semicircular key seats half in...
View full detailsO-Ring seals a joint within the carburettor assembly of the fuel system. It provides a fuel-tight seal at the carburettor interface, preventing le...
View full detailsBonnet Striker Kit - the striker for the bonnet locking assembly. The striker is the fixed catch plate that the bonnet lock and safety catch engage...
View full detailsModule
Synchro Pair
Wiper Drive Tube is part of the windscreen wiper drive mechanism, guiding the drive between the wiper motor and the wheelboxes. It houses the flex...
View full detailsSpeedometer Cable for the Land Rover speedometer drive system. Transmits rotational drive from the gearbox output shaft to the speedometer head, pr...
View full detailsPower Steering Pipe forms part of the power steering hydraulic circuit, carrying pressurised fluid from the steering pump to the steering box. The...
View full detailsFuel Vent Pipe forms part of the evaporative loss control system within the petrol fuel circuit. It routes fuel vapour away from the tank so the e...
View full detailsSteering Wheel Cover is the centre pad that fits over the hub of the steering wheel, concealing the column nut and finishing the centre of the wheel.
Upper Body Trim Bracket for the left-hand side, forming part of the exterior body trim assembly. This bracket provides a secure fixing point that ...
View full detailsSpare Wheel Bonnet Ring is the mounting ring on which a bonnet-mounted spare wheel is seated. It provides the seating face that the wheel rim loca...
View full detailsShim Washer used in the steering box assembly to adjust end-float and pre-load during overhaul or reassembly. Fits the recirculating-ball steering ...
View full detailsInsulator
Speed Sensor for the transfer gearbox speedometer drive. This 2-pin inductive sensor reads a toothed reluctor on the transfer box output, generatin...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →