for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...
View full detailsFront seat headrest in Techno trim, forming the upper part of the front seat assembly. The headrest locates on its stems into the guide sleeves se...
View full detailsCable Connector is a four-way electrical connector body used in the vehicle wiring harnesses. It joins a harness branch to its mating half, retain...
View full detailsGrab Handle in grey, for the cabin interior trim. It provides a fixed hand hold for occupants entering, exiting or bracing themselves within the ve...
View full detailsCentre Silencer for the exhaust system on the 2.4L and 2.2L TDCi (Puma) turbo-diesel. The silencer forms the middle section of the exhaust, sittin...
View full detailsEGR Valve for the exhaust gas recirculation circuit on Td5 2.5L 5-cylinder turbo diesel and 2.0L L-Series diesel engines. The valve meters a contr...
View full detailsCoolant Hose - Expansion Tank connects the coolant expansion tank into the engine cooling circuit. It routes coolant between the expansion tank an...
View full detailsPTO Shaft - Centre - the centre shaft in the power take-off (PTO) drive train. The power take-off transmits rotational drive from the transfer gea...
View full detailsFuel Shut-Off Switch for the Td5 diesel fuel system - an inertia-operated safety switch wired into the fuel pump supply circuit. In the event of a...
View full detailsGear
Door Lock Assembly - left-hand front door lock and exterior handle assembly, non-slam type. This unit combines the door latch mechanism with the o...
View full detailsFuel Pipe - Accumulator To Filter is a formed rigid fuel line in the V8 fuel injection supply circuit. It carries pressurised fuel from the outlet...
View full detailsCarburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...
View full detailsO-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...
View full detailsLocking Nut used to secure the facia moulding. The self-locking nut resists loosening under vibration, retaining the facia panel fixing.
Glazing Rubber - rear side door window lift channel seal for 5mm glass. The rubber lines the window lift channel of the wind-up rear side door, lo...
View full detailsHeater Cable is the air distribution control cable for the heater assembly. It connects the heater control on the facia to the air distribution fl...
View full detailsPlastic Clip for the radiator and fan cowl assembly. The clip locates the cowl to the radiator and retains the surrounding cooling system trim, ho...
View full detailsBlanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...
View full detailsInlet Manifold forms part of the engine air intake system, distributing the intake charge to the cylinder head inlet ports. Fitted to the 2.5-litr...
View full detailsSealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...
View full detailsPower Steering Hose forms part of the power steering hydraulic circuit. It carries hydraulic fluid through the steering assist system, connecting ...
View full detailsShim bearing differential 0.062""
Exhaust Clamp a clamp for the exhaust system on 4-cylinder TDi applications. It secures the joint between two exhaust sections, holding the pipes ...
View full detailspipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole
Exhaust Downpipe Bracket for the front section of the exhaust system. Locates and supports the front exhaust downpipe against the engine/chassis, ...
View full detailsGrommet - moulded rubber grommet for a panel or component aperture. Fitted into a drilled or pressed hole to line the opening, it provides a seal ...
View full detailsExhaust Pipe Clamp for the front exhaust pipe joint. Clamps the front exhaust pipe at its connection, holding the joint tight and gas-tight agains...
View full detailsFemale Dovetail for the rear end door latch mechanism. Receives the male dovetail to align and secure the rear door as it closes. Sold individually.
Screw - an M6 x 20 mm pan-head setscrew with a Torx drive, used as a general multi-application fastener. The Torx socket gives positive tool engag...
View full detailsTurbo Oil Feed Pipe delivers pressurised engine oil to the turbocharger, part of the turbocharger lubrication circuit. Fitted to the 2.2L 16V TDCi...
View full detailsSpeedometer for the instrument cluster, displaying road speed on non-EFI applications. It mounts in the dashboard instrument panel and is driven b...
View full detailsThrust Washer for the LT95 four-speed gearbox, 3.75mm thickness. This selective-thickness washer sets the end-float of the intermediate gear.
Steel Road Wheel - 6.5J x 16, Wolf-style pattern. It provides the mounting surface for a tubeless road tyre and transfers vehicle load from the tyr...
View full details36 Spline Steering Wheel with a black leather rim. It mounts on the 36 spline upper steering column shaft and is retained by the column nut. The s...
View full detailsExterior Rear-View Mirror - door-mounted outer mirror supplied complete with its mounting arm. Mounts to the front door and gives the driver the r...
View full detailsFiller - Rear Quarter Panel
Pipe Adaptor is a double-male union fitting in the automatic transmission oil cooler circuit. It joins two pipe runs, carrying transmission fluid ...
View full detailsNeedle Valve Kit Float-chamber needle valve and seat for the Zenith Stromberg 175CD carburettor, fitted to the 3.5L V8 petrol engine. The needle v...
View full detailsRear Seat Bracket outer right-hand mounting bracket for the rear seating, securing a forward-facing individual rear seat to the floor. Locates the...
View full detailsSplit Pin is a 1.5 mm x 10 mm securing pin used to lock a castellated nut or to retain a clevis pin. It passes through a drilled hole, and its two ...
View full detailsDoor Hinge mounts the front door to the body at the A-post, carrying the door's weight and setting its swing and closing alignment. This is the upp...
View full detailsRadiator Bottom Hose connecting the radiator outlet to the engine thermostat housing within the cooling circuit. It returns cooled coolant from th...
View full detailsCoolant Adaptor (Reducer) - threaded adaptor in the engine oil cooler circuit at the radiator. This threaded reducer adaptor connects the engine o...
View full detailsDoor Check Strap Channel is the channel of the front door check strap (checker) assembly. It guides and retains the check strap as the door swings,...
View full detailsFuel Filter Centre Bolt for the diesel fuel filter and sedimentor assembly. This through-bolt clamps the filter bowl and element onto the filter h...
View full detailsBody-to-Chassis Mounting Bracket in the chassis-frame body mounting assembly of the 110 and 130 Defender, including the High Capacity Pick Up. It ...
View full detailsElement - Air Cleaner
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →