for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Mudguard - Power Take Off for the centre power take-off (PTO) housing. Mounted to shield the centre PTO unit from mud, water and road debris. Prot...
View full detailsLocking Wheel Nut Key engages the matching pattern locking wheel nut so it can be fitted and removed with a wheel brace or socket. This key matche...
View full detailsTurbocharger Oil Drain Pipe in the turbocharger lubrication circuit of the 2.5L four-cylinder turbo diesel engine. It returns oil from the turboch...
View full detailsTorx Pan-Head Screw, M5 x 25. Secures the radiator grille and rear end door casing trim.
Sunroof Finisher is a trim finisher for the sunroof assembly. It frames the edge of the sunroof aperture, concealing the join between the sunroof ...
View full detailsExhaust Bracket locates and supports the exhaust system, securing a section of the exhaust to the underbody to control movement and isolate vibration.
Plate Nut - RH for the front door latch striker on the Defender. The plate nut is fixed to the door pillar on the right-hand side and provides the...
View full detailsFiller Strip for the fixed side window aperture, part of the body glazing assembly. The strip fills and finishes the gap around the fixed side win...
View full detailsA-Post Finisher is the trim cover for the right-hand A-post, the windscreen pillar, concealing the pillar structure and dressing the join between t...
View full detailsGearbox Retainer - LT77
Door Latch Adjuster. Part of the door latch mechanism, it sets the striker engagement so the door aligns, closes and seals correctly. It serves the...
View full detailsFinger Pull for the side door sliding glass window. The outer grip fitted to the sliding glass pane, used to slide the window open and closed.
Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...
View full detailsPower Assisted Steering Hose for the hydraulic power steering circuit, specific to left-hand drive applications. This pipe forms the return leg of...
View full detailsOil Filter Housing Adaptor - part of the oil filter and oil cooler assembly. It mounts on the oil filter housing and provides the connection betwee...
View full detailsscew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)
"Td5" Decal - black engine-designation decal, approximately 13 cm, identifying the Td5 diesel engine variant. Applied to the exterior body as an e...
View full detailsFuel Pipe for the fuel delivery system on the 2.5-litre four-cylinder diesel engine, routing fuel along the supply line towards the injection pump....
View full detailsDowel for the manual gearbox gear-selector assembly. It locates the selector components against the housing to hold their alignment during gear eng...
View full detailsBolt Exhaust manifold fixing bolt, 5/8" UNC x 5-1/2", for the 3.5L V8 petrol engine. Secures the exhaust manifold to the cylinder head within the ...
View full detailsRivet - 3.2 x 8 mm body and chassis fastener. Used in the rear end door check mechanism (lever type), spare wheel carrier mountings and auxiliary ...
View full detailsGearshift Lever Seal seals the base of the gear lever where it enters the manual gearbox housing. It prevents oil loss from the gearbox and keeps ...
View full detailsSelf-Tapping Screw used to secure the rear lamp assemblies - the reflectors, fog lamp and reverse lamp - to the body. The self-tapping thread form...
View full detailsTailgate Hinge Bolt secures the tailgate hinge to the rear body in the tailgate hinge assembly. Used on High Capacity Pick Up (HCPU) body configur...
View full detailsRocker Cover for the 2.5L naturally aspirated diesel and 2.5L turbo diesel engines. It encloses the rocker gear at the top of the cylinder head an...
View full detailsDifferential Thrust Washer for the four-pinion differential in the Land Rover-type axle. Seats behind a differential gear to control end-float and...
View full detailsMainshaft Spacer for the LT77 five-speed manual gearbox fitted to V8 models. Locates on the gearbox mainshaft to set the correct axial spacing and...
View full detailsGearbox Mainshaft Shim for the manual transmission gearbox. Used during gearbox assembly or overhaul to set correct mainshaft end-float. Selecting...
View full detailsThrottle Spring - the return spring in the throttle linkage. Acting on the throttle body spindle, it closes the throttle butterfly and returns the ...
View full detailsAccelerator Return Spring for the throttle linkage on V8 EFI petrol engines. Returns the throttle to the closed position when the accelerator is r...
View full detailsWiper Cable Tube - Motor To Wheelbox
Centre Floor Heelboard Carpet - left-hand section, finished in Ebony (black). This moulded carpet section trims the centre floor heelboard on the ...
View full detailsCentre Floor Heelboard Carpet - right-hand section, finished in Ebony (black). This moulded carpet section trims the centre floor heelboard on the...
View full detailsIntake Air Valve Assembly is the rubber dust valve fitted to the base of the air cleaner housing in the engine air intake system. This one-way fla...
View full detailsSnap Ring is a retaining ring that seats into a machined groove to locate a component on a shaft or within a bore, holding it against axial movement.
Engine Mounting rubber, a bonded rubber-to-metal mount that sits between the engine or gearbox mounting bracket and the chassis. It carries the we...
View full detailsHi/Lo Range Gear is a range gear within the LT230 transfer box. The transfer box splits drive from the gearbox to the front and rear axles and pro...
View full detailsFuel Tank Change-Over Tap is a manual selector valve for twin fuel tank installations. It is used at the heelboard and at the rear tank, and switc...
View full detailsHeadlamp mounting panel RH
Hoodstick Tube Guide is a tubular member of the soft top hood frame, locating and tying the hood sticks together to brace the folding frame that su...
View full detailsWindow Regulator Assembly for the side door glass, right-hand side. Part of the door window lift mechanism. The regulator mounts inside the door s...
View full detailsBracket KVU100220
Heater Hose forming part of the cabin heater coolant circuit, carrying feed coolant from the engine cooling system to the heater matrix. For the 2...
View full detailsTow Bar Assembly is the rear towing attachment that provides the vehicle's hitching point, mounting to the rear chassis crossmember. The assembly ...
View full detailsBrake Pipe Assembly for the rear brake hydraulic circuit. The rigid pipe carries pressurised brake fluid along the chassis to the right-hand rear ...
View full detailsInlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...
View full detailsPipe
Wastegate Actuator Pneumatic actuator that regulates turbocharger boost pressure on the 2.5L 200TDi turbo diesel engine. Mounted on the turbocharg...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →