for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
3rd Speed Gear for the R380 five-speed manual gearbox, cut with 27 teeth. The gear sits on the mainshaft within the R380 constant-mesh gear cluste...
View full detailsPower Steering Pump Pulley mounts on the power steering pump shaft within the steering hydraulic circuit. Driven by the auxiliary drive belt, it t...
View full detailsAlloy Wheel - a 7J x 16" five-spoke cast alloy road wheel with a dual (two-tone) finish. The spoke face carries embossed lettering as a styling de...
View full detailsFuel Injection Pump Gear Retainer is a workshop special tool used when removing or refitting the fuel injection pump on the TDi diesel engine. It ...
View full detailsHand Throttle Cable is the secondary throttle control cable, operated by a hand control rather than the accelerator pedal. It holds the throttle l...
View full detailsOil Cooler Hose forms part of the engine oil cooling circuit, carrying oil between the engine and the front-mounted oil cooler. It feeds hot oil t...
View full detailsVacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...
View full detailsRelay is a 12V 60A change-over relay used in the vehicle electrical system to switch a high-current circuit through a low-current control signal. ...
View full detailsOuter Door Handle is the external grab handle for the right-hand door, part of the door latch mechanism group. Mounted on the outer door skin, the...
View full detailsActuator
Body Side Frame Assembly forms the left-hand structural side frame of the bodyshell. It provides the framework to which the outer body panels, door...
View full detailsRaised Air Intake Kit
Lower Fan Cowl for the Td5 2.5L 5-cylinder turbo diesel engine cooling system. The fan cowl shrouds the engine cooling fan and channels the air dr...
View full detailsCoolant Hose for the engine cooling circuit, connecting the thermostat housing to the coolant pump pipe. Fitted to the 2.4L Td4 four-cylinder turb...
View full detailsHose - Fuel Feed Defender
Expansion Tank - coolant expansion (header) tank for the engine cooling system. The tank accommodates the change in coolant volume as the engine h...
View full detailsAnti-Roll Bar Bracket - Rear secures the rear anti-roll bar to the chassis, forming part of the rear stabiliser bar mounting. The bracket clamps o...
View full detailsSeat Belt Anchor Plate twin anchor plate for the rear seat belt assembly, of the forward-facing outer static type. The plate forms the male anchor...
View full detailsSoft Top Seal header rail to windscreen seal, part of the soft top assembly. Seals the joint between the front header rail of the soft top and the...
View full detailsEngine Wiring Harness is the engine-bay wiring loom connecting the engine's electrical components into the vehicle circuit. This harness is for 30...
View full detailsMain Wiring Harness is the principal vehicle wiring loom, routing power and signals through the body and to the steering column. This harness is f...
View full detailsChassis Wiring Harness - Heated Rear Window & Rear Wiper is the rear body/chassis section of the wiring loom that supplies the heated rear wind...
View full detailsBonnet - Defender
Fuel Tube within the fuel supply line, connecting the fuel tank to the fuel filter. It carries fuel from the tank to the inlet of the fuel filter ...
View full detailsIntermediate Gear for the LT230 transfer case gear train. The intermediate gear is carried on the transfer case intermediate shaft and meshes with...
View full detailsBreather Assembly for the rear axle drivetrain system. The breather allows pressure equalisation within the axle housing, preventing oil seal damag...
View full detailsPad R380
Rear End Door Assembly forms the full-height rear closure of the luggage compartment. Side-hinged, it swings clear to open the rear of the load are...
View full detailsBody Finisher - Rear Capping - RH for the rear body on the Defender 110 two-door hard top and soft top. This right-hand rear body capping finisher...
View full detailsRadiator Grille finished in Brunel Grey, forming the central section of the front-end body panel. The grille locates in the front panel aperture a...
View full detailsAlternator Bearing Kit for the drive end of the Lucas A133 alternator. It renews the bearing at the pulley (drive) end of the rotor shaft, which su...
View full detailsRear Fog Lamp is part of the rear lighting assembly, mounted at the rear of the vehicle. The lamp produces a high-intensity red light to improve t...
View full detailsFuel Pump Assembly Complete fuel pump unit in the fuel delivery system, drawing fuel from the tank and supplying it to the engine under pressure. ...
View full detailsStrap fuel tank Defender 110 TD5/TD4
Rubber Floor Mat Set - Front for the front footwells, supplied as a matching pair. The mats are moulded in rubber to protect the front floor area a...
View full detailsWaterproof seat cover for a single outer front seat, finished in grey. The cover is shaped to the standard seat frame and fits over the existing u...
View full detailsProtector Lamp
Bolt Set Screw 7/16UNC x 1.25" 2.25L diesel: startermotor to engine (Imperial, non-metric engines) 2.6L petrol: oil filter housing to adaptor
Rear Floor Mat Set is a drop-in moulded rubber mat set for the rear floor area. The mats locate over the rear footwell and floor pan to protect th...
View full detailsAlternator Brush Set - the carbon brushes for the alternator, part of the charging circuit. The brushes bear on the rotor slip rings to carry field...
View full detailsRear Fog Lamp Switch for the facia switch panel. The switch operates the rear fog lamp within the exterior lighting circuit.
Coolant Temperature Sensor - screws into the thermostat housing as part of the engine cooling system. It senses coolant temperature in the thermos...
View full detailsPolyvee Auxiliary Drive Belt running in the engine front-end auxiliary drive, transmitting rotational drive from the crankshaft pulley to the alter...
View full detailsFuel Cooler for the diesel fuel return circuit. Mounted in the return line between the fuel injection system and the tank, it dissipates heat pick...
View full detailsSpring Pin for use in the engine assembly. A cylindrical spring pin (roll pin) used to locate or retain internal components within the engine.
Fuel Spill Pipe from the fuel tank and pump mounting assembly, used on petrol applications. The spill (return) pipe carries the fuel not consumed ...
View full detailsFoam Dunlop Washer
Heater Hose connecting the heater to the engine coolant pipe, part of the heater pipes and hoses assembly. The hose forms part of the coolant path...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →