Land Rover Old Defender 90, 110 & 130 Parts

Fitment: - Classic Defender: TD5 diesel models - Discovery 2: All TD5 diesel models and All V8 EFi petrol models - Range Rover P38: 2.5L 6 Cyl B...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Plain Washer is a flat fastening washer fitted under a bolt head or nut to spread the clamping load across a wider area and protect the mating surf...

Screw is an M4 x 8mm fastener used in the door mirror assembly, securing components of the interior and exterior mirrors at their mounting points. ...

Folding Side Step Mat - tread mat fitted to the folding side access step. Provides a non-slip stepping surface for entry and exit at the side doors.

Tab Washer for the steering box drop arm retaining nut. This lock washer sits under the nut on the steering box output shaft. Once the nut is torq...

Speaker Bezel is the trim surround that frames a speaker opening in the interior. Part of the in-car entertainment (ICE) installation, it finishes...

Spring Ring

Saddle Clip for routing and securing the power steering pipes. This saddle-shaped clip clamps the power steering hydraulic pipes to the chassis or...

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Air Filter Strap securing the air cleaner housing within the engine intake system. Clamps the air filter canister to its mounting on the 2.5L four...

Centre Handle Cover is the screw cover cap for the window winder handle, finished in black. This small cover conceals the retaining screw on the m...

Switch

Rear Fog Lamp Switch is the dashboard-mounted control for the rear fog lamp circuit. This switch allows the driver to activate the rear fog lamp f...

Exhaust manifold stud

Lock Washer secures the retaining hardware on the layshaft (countershaft) within the manual gearbox. A tab on the washer is folded against the ret...

Front Screen Timer Relay is the grey timer relay within the heated front windscreen circuit. When the heated screen is switched on, this relay ene...

Heater Hose forming part of the engine coolant circuit that supplies the heater matrix. This is the feed hose carrying heated coolant from the eng...

Fuel Tank Vent Hose - part of the fuel tank ventilation circuit on Puma TDCi models. It carries fuel vapour from the tank, allowing the tank to br...

Pump Injection Ring

Gear Selector Ball End is the ball-joint pivot in the gear change selector linkage, connecting the selector rod to the transmission operating shaft...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Bolt - M8 x 50 - Torx is an M8 threaded fastener, 50 mm long, with a Torx drive head. It is used as a general-purpose fixing across a range of bod...

Headlamp Screw is a fastener used in the front headlamp assembly. It secures the headlamp unit and rim within their mounting, holding the lamp in ...

Front Brake Anchor Plate (back plate) for the right-hand side, part of the front drum brake assembly. The anchor plate bolts to the axle and carri...

Intercooler to Turbocharger Hose is part of the charge-air (boost) system. It carries pressurised air between the turbocharger and the intercooler...

Oil Filter Gasket for the four-cylinder 2.25L/2.5L petrol and 2.5L naturally aspirated diesel engines, part of the engine lubrication circuit. The...

Cigar Lighter Mounting Plate, the fascia panel that carries the cigar lighter unit. It mounts into the dashboard fascia, locating and retaining th...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Gearbox Filter Plug for the LT77 five-speed manual gearbox. The plug closes the bore in the extension case that gives access to the gearbox oil fil...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Locking Nut A locking nut for the gear lever plunger in the gearchange mechanism of the 5-speed manual gearbox. It retains the spring-loaded plung...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Set Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...

Detent Spring for the LT77 and R380 manual gearbox gear change mechanism. This spring forms part of the selector detent assembly within the gearbo...

Packing Strip fitted between the bulkhead base and the footrest bracket mounting on the chassis of Defender 90/110. This strip provides the correc...

Clevis Pin for the differential lock selector linkage in the LT230 transfer gearbox. This clevis pin secures the selector lever pivot that actuate...

Flywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...

M6 Stud for the gearbox main casing. This threaded stud secures the speedometer drive housing to the transmission main casing, providing the fixin...

Front Seat Belt Assembly for the Defender occupant restraint system. This complete front seat belt assembly includes the belt, retractor, and buck...

Exhaust U-Bolt secures a joint in the front section of the exhaust system. The U-bolt clamps over the pipe at a slip joint and, tightened against i...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Fuel Injector Bolt - retaining bolt securing the fuel injector clamp to the cylinder head on the 2.4L Duratorq TDCi (Puma) common-rail diesel engin...

Gear Lever Anti-Rattle Plunger Spring The lower plunger spring for the gear lever in the gearchange mechanism of the 5-speed manual gearbox (LT77 a...

Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...