for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Centre Console Blanking Panel for the Defender 90 and 110. Fills an unused aperture in the centre console, providing a clean, finished appearance ...
View full detailsSill Panel - LH for the Defender 110 Station Wagon and Crew Cab body variants, forming the exterior body panel along the left-hand lower sill line ...
View full detailsRoof Seal Retainer is a fixing strip within the roof assembly that secures the roof weather seal, clamping the seal in place where the roof panel m...
View full detailsGear Lever Spacer for the manual gearbox gear change assembly. It sets the position of the gear lever within the gear change housing, maintaining t...
View full detailsRear Door Seal for the rear door aperture on Series III and Defender 90 and 110. The rubber seal runs around the perimeter of the rear door apertu...
View full detailsHeater Hose - outlet pipe from the heater matrix, Td5 2.5L 5-Cylinder Turbo Diesel, left-hand drive (LHD). Returns engine coolant from the heater ...
View full detailsWiper Spindle Seal is the seal for the windscreen wiper spindle. It fits around the wiper spindle where it passes through the bulkhead, sealing th...
View full detailsWiper arm Defender RHD 2A on
Defender 110 Decal - black, approximately 26cm length. Self-adhesive black Defender 110 model identification decal from the Defender transfers and...
View full detailsBody Decal reading 'Defender 110' - an exterior self-adhesive graphic finished in silver lettering on a clear backing. The decal is applied to the...
View full detailsLand Rover Logo Tape - adhesive decal, 25cm length. Self-adhesive Land Rover logo tape from the Defender transfers and graphics range. Applied to ...
View full detailsDoor Panel is the inner panel of the left-hand front door. The panel forms the structural inner face of the door shell, carrying the mountings for...
View full detailsDoor Panel is the inner panel of the right-hand front door. The panel forms the structural inner face of the door shell, carrying the mountings fo...
View full detailsCarburettor Overhaul Kit for the 2.25L four-cylinder petrol engine. The kit renews the perishable sealing and metering components of the carburetto...
View full detailsControl Unit - dim dip lighting module for the Defender electrical system. This module operates the dim dip lighting circuit, activating the headl...
View full detailsRear Window Heated Switch
Heater Control Label - replacement decal for the heater control panel. Fits within the HVAC control assembly and provides the printed markings ind...
View full detailsBulb Holder A black bulb holder that retains a bulb and connects it into the lighting circuit. Used in the instrument panel and interior trim ligh...
View full detailsShakeproof Starlock Washer used within the clutch master cylinder and pipe assembly. The washer pushes onto a plain shaft or pin and grips it with...
View full detailsMulti-Height Tow Bar is a towing assembly for the high-capacity pick-up and crew cab body styles, mounting to the rear of the chassis. The multi-h...
View full detailsMainshaft for the R380 5-speed manual gearbox. The mainshaft is the central driven shaft within the R380 gearbox, carrying the output gear cluster...
View full detailsClutch Damper for the Defender Puma hydraulic clutch circuit. This in-line hydraulic damper installs within the clutch hydraulic hose run between ...
View full detailsBlade Wiper (LR009343 ) - Series 5mm
Brake Pipe T-Piece is a three-way hydraulic union in the rear braking circuit, joining the incoming brake line to the two rigid pipes that feed the...
View full detailsPan Head Bolt, M8 x 40mm. Metric pan head bolt for use across Land Rover body, chassis, and interior assemblies.
Piston ring set petrol 2,25 020 Mahle (per zuiger)
Rear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...
View full detailsWater Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...
View full detailsRadiator Bottom Hose is the lower coolant hose of the engine cooling circuit. It carries cooled coolant from the radiator's lower outlet back to t...
View full detailsSplit Pin is a cotter-type retaining pin used to lock a clevis pin or pivot pin in position. It passes through the cross-drilled end of the pin an...
View full detailsChassis Mounting Plate is a spreader plate for the body mounting bracket, fitting at the chassis outrigger where the body is secured to the chassis...
View full detailsSecure your bonnet-mounted spare wheel with this heavy-duty retainer bracket. This ring-type spare wheel retainer ensures a stable and secure fitme...
View full detailsHandbrake Cover - the trim cover fitted around the base of the handbrake (parking brake) lever where it mounts on the transmission tunnel. It conc...
View full detailsBonnet Staple - the fixed engagement point within the hand-operated bonnet locking assembly. This component mounts to the bonnet panel and interfa...
View full detailsTank to Fuel Filter Tube
Heater Cable Assembly for the heating and air conditioning control system. The cable links the dashboard heater control to the heater box, transmit...
View full detailsBody Side Step is a folding side step for the Defender, mounting to the body sill to provide a step for vehicle entry and exit. The step folds fla...
View full detailsFront Brake Disc Shield - Defender This pressed-steel shield fits behind the front brake disc on the Defender, located between the disc and the sw...
View full detailsBreather Assembly vents the front axle housing, letting trapped air escape and equalising internal pressure as the differential oil heats and cools...
View full detailsFlywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...
View full detailsFuel Pipe for the 200 TDi diesel fuel delivery circuit. Connects the fuel filter outlet to the injection pump inlet, carrying filtered fuel to the...
View full detailsEngine Plug - a cylinder head core plug (welch plug) for the Td5 2.5L 5-cylinder turbo diesel engine. Core plugs seal the casting holes left in th...
View full detailsInjector Spill Pipe links the fuel injectors in the 2.5L 4-cylinder turbo diesel injection system. It returns leak-off (spill) fuel from the injec...
View full detailsClutch Pedal Spring Bush is a small bush fitted to the clutch pedal assembly on the Defender 90/110, locating the pedal return spring. The bush se...
View full detailsDomed Nut - retains the dash ventilator (face-level fresh-air vent) in the facia. Used on vehicles without air conditioning. The domed (acorn) for...
View full detailsTruck Cab Waist Seal for the Land Rover Defender truck cab body variant. This rubber seal fits at the waist level of the truck cab body, sealing t...
View full detailsBolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...
View full detailsBolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →