for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Woodruff Key for the V8 petrol engine. A semicircular (half-moon) key that seats in a shaft keyway to angularly locate and lock a mating gear, pull...
View full detailsCover Assembly - water jacket cover for the inlet manifold plenum chamber. It closes off the coolant water jacket passage within the plenum chambe...
View full detailsCirclip a spring-steel retaining ring that seats in a machined groove to axially locate a component on a shaft or within a bore. Used in the diffe...
View full detailsWoodruff Key - Crankshaft for the Rover V8 petrol engine. This semi-circular key locates the crankshaft timing sprocket and harmonic balancer to t...
View full detailsWiring Clip for securing and routing electrical harnesses in Land Rover vehicles.
Tow Hitch for the towing system, rated to a maximum gross towing weight of 3,500 kg. The hitch bolts to the tow bar and carries the tow ball, prov...
View full detailsTransfer case gear set for the LT230 transfer box, providing a modified high-range ratio of 1.667:1. Replaces the stock planet gears in the LT230 ...
View full detailsAir-operated differential locker for a 24-spline differential, replacing the standard differential centre in the axle. When engaged, it locks both...
View full detailsSynchroniser Assembly for 3rd and 4th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The assembly locks the selected gear t...
View full detailsCoolant header tank in aluminium, forming the expansion and filling point of the engine cooling circuit. The tank absorbs the change in coolant vo...
View full detailsSynchroniser Assembly for 5th gear, mounted on the mainshaft of the R380 five-speed manual gearbox. The sliding sleeve is moved by the fifth-gear ...
View full detailsTransfer Box Overhaul Kit for the LT230 transfer box. The LT230 is the two-speed transfer box that splits drive from the gearbox between the front...
View full detailsPiston Ring Set for the 3.9 litre Rover V8, supplied at standard size and covering one piston - eight sets are required to do a complete engine. T...
View full detailsInjector O-Ring is a sealing ring fitted to a fuel injector in the V8 EFI (electronic fuel injection) system. It seals the injector against its mo...
View full detailsBrake Pipe Connector - a junction fitting in the hydraulic brake circuit that joins rigid brake pipes. It provides a sealed connection between bra...
View full detailsTow Hook Cover is a protective cover for the 50mm tow hook. It fits over the towing hook to protect it when not in use and to give a finished appe...
View full detailsHydraulic Jack & Handle - the vehicle-supplied lifting equipment carried in the on-board tool kit for wheel changes and roadside servicing. Th...
View full detailsAlternator for the V8 EFI petrol charging system, rated at 100A. This is the A127-type alternator assembly, belt-driven from the crankshaft pulley ...
View full detailsPlain Washer - flat unthreaded washer used within the differential assembly. It seats in the differential case at the crownwheel and pinion, provi...
View full detailsRocker Shaft Spring for the Rover V8 valvetrain, fitted on the rocker shaft assembly. The spring acts as a spacer between adjacent rocker arms, ho...
View full detailsTow Ball & Pin is a towing coupling component that mounts to the tow bracket or drop plate. The ball provides the coupling point onto which a ...
View full detailsCable Tie is a harness fixing used to bundle and route wiring looms, hoses and cables against the chassis and body. It secures the harness in posi...
View full detailsFuel Pipe Union Nut for the fuel delivery line. This female threaded nut draws a fuel pipe up to its mating union, clamping the pipe's flared or c...
View full detailsWasher Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...
View full detailsBolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...
View full detailsFront Cover Oil Seal is the crankshaft front oil seal. It is pressed into the engine front (timing) cover and seals the crankshaft where it passes ...
View full detailsStop/Tail Bulb - 12V 21W - Twin Pack (trade reference 380). This pack contains two BAY15d dual-filament bayonet bulbs rated 12V 5/21W, suitable fo...
View full detailsAir Flow Sensor for the V8 EFI petrol engine management system, mounted in the intake tract between the air filter and the throttle. Measures the ...
View full detailsFuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...
View full detailsFuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...
View full detailsStepper Motor for the V8 EFI petrol engine, part of the idle air control system on the intake plenum. Acts as the idle air control valve, metering...
View full detailsValve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...
View full detailsNyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...
View full detailsBow Shackle Bow-shaped recovery shackle with a threaded pin, used to connect a recovery strap or rope to a recovery point on a winch bumper. The w...
View full detailsElbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...
View full detailsBody Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...
View full detailsBrake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...
View full detailsTowing Bracket Slider Lock Pin is the pin that locks the vertical slider of a Dixon Bate adjustable-height towing bracket at the selected height. ...
View full detailsClutch Hose for the 300 Tdi 2.5L turbo diesel, forming the flexible section of the clutch hydraulic actuation circuit. The hose links the rigid pi...
View full detailsCoolant Temperature Sensor - V8 EFI for the engine management system. This sensor monitors coolant temperature and sends a continuous signal to th...
View full detailsBulb, 12V 4W (type 233, BA9s single-contact bayonet cap), supplied as a twin blister pack of two bulbs. A miniature bayonet bulb used in number pla...
View full detailsHose - Oil
Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...
View full detailsClutch Slave Cylinder Repair Kit - a service kit for reconditioning the hydraulic clutch slave cylinder on the R380 5-speed manual gearbox. The cl...
View full detailsTaper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...
View full detailsLayshaft Bearing - taper roller bearing supporting the layshaft in the R380 5-speed manual gearbox. The bearing carries the countershaft (layshaft...
View full detailsOil Seal for the R380 manual gearbox extension case (rear/tail housing). It seals the output shaft where it exits the extension housing, retaining...
View full detailsCore Plug for the V8 petrol cylinder block and inlet manifold. The cup-type plug seals the casting core holes left in the coolant jacket after man...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →