Land Rover Old Defender 90, 110 & 130 Parts

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Joint washer

Gear Knob - gear lever knob for the R380 5-speed manual gearbox. Threads onto the gearchange lever, forming the driver's hand grip and gear-select...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Speedo drive oil seal LT230

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Shock Absorber Bush for the lower mounting of a suspension damper. The rubber bush seats in the shock absorber's lower mounting eye, locating the ...

Slipper pad

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Spark Plug Ignition component for the Rover V8 petrol engine. Threaded into the cylinder head, it carries the high-voltage current from the igniti...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Locking plate

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Pinion oil seal

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Grommet

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Rocker Cover Gasket for the V8 petrol engine, cork construction. The gasket seals the joint between the rocker cover and the cylinder head, contai...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

screw M5 x 12

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...