for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Differential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...
View full detailsFront Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...
View full detailsTiming Chain Tensioner maintains correct tension on the timing chain within the engine timing case, preventing chain slap and ensuring accurate val...
View full detailsBall Race - Steering Box (Adjusting) is a component of the recirculating-ball manual steering box assembly, used to control pre-load and end-float ...
View full detailsMainshaft Thrust Washer - 2nd Gear (0.125") is a selective shim located within the Series gearbox, fitted to control axial play on the second gear ...
View full detailsFront Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...
View full detailsWhite 8 Spoke rim 16" x 7" - welded - tubeless
Washer
Seat Box Corner Protector set, supplied as a pair to guard the exposed corners of the seat box against knocks and wear. Each protector is CNC cut ...
View full detailsUniversal Joint for the propeller shaft, measuring 75 mm across the bearing caps with a 27 mm cap diameter. The universal joint is the cross-and-b...
View full detailsHalo & Bar 7" LED Headlights - a pair of sealed LED headlamp units that replace the original lamps in a traditional 7" round headlamp aperture,...
View full detailsSliding Window Kit - Deluxe, supplied as a pair for the rear body sides. The kit fits a horizontally sliding glass window into the rear side panel...
View full detailsSliding Window Kit - Deluxe, supplied as a pair for the rear body sides, with grey tinted glass. The kit fits a horizontally sliding glass window ...
View full detailsCrystal Headlamp - a matched pair of 7-inch round crystal halogen headlamps for right-hand-drive applications. The clear (crystal) lens and facete...
View full details7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...
View full details7" Crystal Halogen Headlamp - round headlamp unit for the front lighting assembly, supplied as a matched pair. The clear crystal lens works with a...
View full detailsUpper Tailgate Lock Cap for the rear end door handle assembly. This small plastic cap fits over the end of the upper tailgate handle, covering and...
View full detailsSelf-Tapping Screw for body and trim fixing applications. Used to secure window surrounds, bodyside trim, facia and switch panels. The self-tappin...
View full detailsT-Piece Hose Connector is a three-way junction fitting used in a flexible hose run. It joins three hose ends at a single point, allowing a hose li...
View full details7 Inch Round LED Headlamp for the front lighting system, replacing the conventional 7-inch round sealed-beam or halogen headlamp. The LED light so...
View full detailsPolyurethane Bush Set in yellow, supplied for suspension mounting points that use a rubber-style bush. Supplied as a set of yellow polyurethane bu...
View full detailsGirling Shock Absorber for the front suspension, a hydraulic damper for heavy-duty suspension applications. Mounted between the axle and the chass...
View full detailsRotor Arm for the Lucas distributor in the ignition system of the 2.0L and 2.25L 4-cylinder petrol engines (up to engine suffix C). Driven by the ...
View full detailsOil Pressure Switch for the engine lubrication system warning circuit. This pressure-sensitive switch threads into the engine block oil gallery an...
View full detailsDrive Flange Gasket
Inner Tube for 7.50 x 16 and 7.00 x 16 tyres, fitted inside the tyre on tube-type wheels to hold the air pressure. Supplied with a small diameter ...
View full detailsBraided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...
View full detailsRubber isolator clamp used in the bonnet-mounted jack bracket assembly to secure the jack beam or handle against the bonnet mounting brackets. The...
View full detailsHeadlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...
View full detailsDrive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.
Steel Ball for the timing chain tensioner, 7/32 in diameter. Seats within the tensioner mechanism to help maintain correct timing chain tension.
Steel Road Wheel - 6.5J x 16, Wolf-style pattern. It provides the mounting surface for a tubeless road tyre and transfers vehicle load from the tyr...
View full detailsbush shock absorber OEM, bush anti roll bar OEM
Steel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...
View full detailsRestore the structural integrity of your Defender 90/110 or Series SWB/LWB with this right-hand side (RHS) bulkhead repair panel, designed for dura...
View full detailsRepair and restore the bulkhead structure of your Defender 90/110 or Series SWB/LWB with this left-hand side (LHS) bulkhead repair panel, designed ...
View full detailsPlain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.
Static Lap Belt - a two-point lap seat belt for a centre or side-facing seating position. The webbing is a fixed length and is adjusted by hand to...
View full detailsInlet Rocker Bush for the valve gear, forming the bearing surface between the inlet rocker arm and the rocker shaft. The bush locates the inlet ro...
View full details3 man seat Techno Exmoor trim EX4188 EXT006-TC
Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...
View full detailsSteel Road Wheel, 5.5J x 16, of welded construction for tube-type tyre fitment. The rim is designed to run with an inner tube rather than a tubele...
View full detailsPortable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...
View full detailsManifold Stud is an M8 x 65 mm threaded stud that secures the inlet and exhaust manifold to the cylinder head on the four-cylinder petrol engine. ...
View full detailsSending is only possible by pallet. Too fragile for normal parcel delivery.
Glass
Door Checker Bracket Assembly - Rear - LH is the door check mechanism for the left-hand rear door. It links the door to the body pillar and limits...
View full detailsBulkhead Repair Panel with Vents - Left-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent sur...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →