for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Stud A threaded fastening stud catalogued for use across multiple applications. It is fitted in several locations on the engine and its ancillarie...
View full detailsRocker Shaft Bush in the cylinder head valvetrain. The bush is pressed into a rocker pedestal and provides the bearing surface that supports the r...
View full detailsSealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...
View full detailsStub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...
View full detailsExhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...
View full detailsBrake Shoe Anchor Plate for the rear drum brake assembly. The anchor plate provides the fixed abutment and locating point for the brake shoes. It ...
View full detailsGrommet seals and protects cables, harnesses and hoses where they pass through body and chassis panels. It is used at wiring harness pass-throughs...
View full detailsRear Door Trim Panel - a black interior trim panel that finishes the inner face of the rear side-hinged door, covering the door frame to give a cle...
View full detailsLamp Boot - Military is a rubber protective boot for military-specification lamp assemblies. The boot fits over the lamp body to provide a weather...
View full detailsSwitch - Fuel Tank Tap is an electrical switch used to operate the fuel tap selection on Land Rover Series I, Series II, Series IIA, and Series III...
View full detailsP-Clip - 19/64" x 3/8" is a pressed-steel P-profile retaining clip used to route and secure fuel lines, brake pipes, or wiring looms against a chas...
View full detailsMounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...
View full detailsValve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...
View full detailsChubby Cubby Box - a between-seats storage box and armrest that mounts on the centre panel of the seat box. It provides lockable interior storage ...
View full detailsCubby Box - Black Mesh
Sidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...
View full detailsCrankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...
View full detailsShock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...
View full detailsFlasher Unit for the direction-indicator circuit, of the 2-pin type without trailer-socket provision. The flasher unit switches the current to the...
View full detailsClutch Driven Plate for the LT95 four-speed gearbox, V8 petrol. The driven plate (friction disc) is splined to the gearbox input shaft and clamped...
View full detailsBolt
Ignition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...
View full detailsMain Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...
View full detailsSnap Ring used within the LT95 4-speed gearbox to retain the inner member to the mainshaft. The LT95 is the 4-speed gearbox with integral transfer ...
View full detailsSet Screw - a fully threaded hexagonal-head setscrew with an M10 metric thread and a 20 mm length. A general-purpose fixing used at fastening point...
View full detailsStrap Stud is a body fixing used in the canvas hood (soft top) and hood frame assembly. It provides an anchor point over which a retaining strap i...
View full detailsCylinder Head to Block Stud for the four-cylinder diesel engines - 2.25L and 2.5L naturally-aspirated. The stud threads into the cylinder block dec...
View full detailsCirclip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...
View full detailsDrop Plate Strengthener for the towing equipment assembly. It acts as a spacer and strengthener for the towing jaw and the towing jaw/ball fixings...
View full detailsBonnet Catch Plate is the mounting plate for the bonnet slam catch, located in the grille and front panel structure as part of the bonnet release a...
View full detailsWindow Seal: rubber glazing seal for the window glass, sealing it against water and draughts.
Rocker Assembly Aluminium - LH
Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...
View full detailsMain Bearing Set for the crankshaft main bearings in the engine bottom end. The bearing shells locate between the crankshaft main journals and the ...
View full detailsWasher is a nylon door hinge washer used on the hinge fixing bolts. It fits over the hinge bolt as a low-friction spacer between the moving hinge ...
View full detailsMud Shield – RHD – LH is the left-hand mud shield for the pedal box. It fits over the pedal box aperture in the bulkhead to keep mud, water and ro...
View full detailsCamshaft Bearing Set for the Rover 3.5L V8 petrol engine. Supplies the bearing shells that support the camshaft as it runs within the cylinder blo...
View full detailsFlywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...
View full detailsRocker Cover Breather Hose - Left-Hand for the crankcase ventilation system of the Rover 3.5L V8 twin-carburettor engine. This hose connects the l...
View full detailsseal washer for block coolant drain plug. - All 4-cylinder engines upto 1998 (except VM diesel)
Clip - 13/64" x 3/8" is a single-bolt retaining clip used to secure wiring harnesses, vacuum lines, and small-bore hoses to body or engine bay brac...
View full detailsRocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...
View full detailsRocker Arm - Steel - LH for the valve train of the Rover V8 engine, part of the Cylinder Head & Valve Train assembly. This steel rocker arm pi...
View full detailsFuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...
View full detailsPlastic Washer serves as a spacing and anti-friction washer at the front seat hinge and the rear door check arm pivot. Fitted at the pivot joint, ...
View full detailsgrab handle for 3rd / 5th door (rear end door). Upto (VIN) 1A622423
Static Three-Point Seat Belt for the front seating position, combining a lap strap and a diagonal shoulder strap in a single restraint. This is a ...
View full detailsGear Lever Damper for the LT95 four-speed gearbox gear-change mechanism. This damping washer fits at the base of the main gear lever, absorbing vi...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →