for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Contact Set for the Lucas distributor fitted to Land Rover petrol engines, comprising the breaker point assembly within the conventional ignition s...
View full detailsContact Set for the ignition distributor of the 3.5L V8 petrol engine. The contact breaker points open and close the primary circuit to the ignitio...
View full detailsWindscreen Clamp - secures the classic fold-flat windscreen frame in its upright position. Mounted at the base of the windscreen frame, the clamp ...
View full detailsDifferential Gear Kit for the Salisbury rear axle. The differential is carried in the centre housing of the rear axle. It takes drive from the pro...
View full detailsSize/Diameter: 1 inch
Piston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...
View full detailsPiston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...
View full detailsPiston ring set petrol 2,25 020 Mahle (per zuiger)
Piston Ring Set for the 2.25L 4-cylinder petrol engine, ground to +0.010" (0.25mm) oversize for use with rebored cylinder bores. The rings seal th...
View full detailsPiston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...
View full detailsPiston for the 2.25L petrol engine, running in the cylinder bore as part of the piston and connecting-rod assembly. Supplied at +0.020" oversize, ...
View full detailsJubilee Hose Clip for securing rubber hoses at coolant pipe, heater hose, and similar fluid circuit connections. The worm-drive band tightens evenl...
View full detailsPrimary Pinion for the LT76 manual gearbox, suffix D onwards. The primary pinion is the gearbox input gear, taking drive from the clutch and passin...
View full detailsWiper Motor Brush Set - the carbon brushes for the windscreen wiper motor. The brushes are spring-loaded contacts that bear on the commutator of t...
View full detailsMain Bearing Set - a set of crankshaft main bearing shells for the Rover V8 petrol engine. The main bearings are the split shell bearings that car...
View full detailsRear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...
View full detailsTube wipersystem OEM
Speedometer instrument head for the dashboard instrument panel, incorporating a resettable trip odometer alongside the main total odometer. The sp...
View full detailsFuel Tank Elbow Pipe installed inside the petrol fuel tank as the fuel pick-up point. This elbow-shaped pipe draws fuel from the base of the tank ...
View full detailsExhaust Tailpipe forming the final section of the exhaust system on the 109" Stage One V8. This pipe routes exhaust gases rearward from the silenc...
View full detailsSpring Washer is a split spring lock washer used at the top of the steering column, at the steering box. Fitted under the securing nut, it maintai...
View full detailsExhaust Downpipe is the front downpipe of the exhaust system for the left-hand (LH) cylinder bank of the V8 engine. The downpipe bolts to the LH e...
View full detailsSpring for Land Rover body and chassis application.
Seat Back - Inner - Standard - Black for the centre position of the three-abreast front bench seat in Land Rover Series vehicles. This vinyl seat ...
View full detailsDoor Top Glass - fixed piece for the Series half-door glazing assembly. This fixed glass panel fits into the top section of the Series half-door f...
View full detailsBulkhead Door Pillar for the right-hand (offside) front door aperture, in the basic configuration. The door pillar forms part of the bulkhead asse...
View full detailsTowing Jaw rated to 3.5 tonnes, part of the towing/pintle hitch assembly. It provides the jaw coupling for trailer and recovery towing, mounting t...
View full detailsFront Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...
View full detailsSynchro Hub is part of the synchromesh assembly in the LT76 gearbox, splined to the mainshaft and carrying the sliding sleeve that engages the gear...
View full detailsRear Left-Hand Half Shaft for the 10/24 spline rear axle. The half shaft transmits drive from the differential to the rear wheel hub. This left-ha...
View full detailsRear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...
View full detailsOil pump relief valve washer V8
Exhaust Valve for the 2.25L 4-Cylinder Petrol engine, fitted in the cylinder head valvetrain assembly. This valve operates in the cylinder head to...
View full detailsFlywheel - 5-Bearing is the rotating mass mounted to the rear flange of the crankshaft in the 5-main-bearing variant of the 2.25L and 2.5L 4-cylind...
View full detailsValve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...
View full detailsValve Spring Cap for the cylinder head valve train. The spring cap seats on top of the valve spring and locates against the split collets on the v...
View full detailsInlet Valve for the cylinder head valve train, with a 34.5 mm head diameter. The inlet valve opens on the induction stroke to admit the air/fuel c...
View full detailsCam Follower - a roller-type tappet operating in the engine valve train, between the camshaft and the pushrod. It rides on the camshaft lobe and t...
View full detailsThrottle Linkage for the 3.5L V8 fitted with twin Stromberg 175CD carburettors. This linkage connects the throttle pedal input to both Stromberg c...
View full detailsFog Lamp Bezel - Anthracite - LH
Tailboard Hinge Bracket Kit provides the bolt-on hinge assembly for a drop-down rear tailboard, mounting the tailboard to the rear body so that it ...
View full detailsTow Hitch Locking Pin (R-Clip) is the spring-steel retaining clip that secures the tow pin in an adjustable tow hitch. It pushes through the hole i...
View full detailsTowing Bracket Slider is the sliding tongue section of a Dixon Bate adjustable towing bracket, which sets and locks the hitch at the required heigh...
View full detailsRear Bumperettes - a pair of tubular bumperettes that bolt to the rear crossmember to protect the rear corners of the body and the rear lamps from ...
View full detailsLoad Bay Liner Kit lines the rear load area to protect the original bed and inner surfaces from cargo abrasion, impact and moisture. The liner is f...
View full detailsLED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...
View full detailsSwivel Shackle - a shackle with an integrated rotating swivel. The swivel lets the connected component turn freely relative to the anchor point, p...
View full detailsDirection Indicator Lamp is a rear amber turn-signal lamp to NAS (North American Specification) pattern in the 95mm round format. It is supplied a...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →