for Discounts / VAT
for Discounts & Correct VAT
Parts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
Plate grommet GENUINE LR
Solonoid
Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...
View full detailsScrew for use in Land Rover body, chassis, and hardware applications.
Shackle Plate, the side plate of the spring shackle assembly that forms the swinging link between the leaf spring eye and the chassis shackle brack...
View full detailsSpring Shackle connecting the end of a leaf spring to the chassis bracket, allowing the spring to lengthen and shorten as it deflects under load. ...
View full detailsBolt used in the LT95 gearbox and transfer assembly. It provides a torque-loaded, clamped fastening securing components within the LT95 transmissi...
View full detailsCam Follower (tappet) in the valvetrain, riding on the camshaft lobe to transmit its motion to the pushrod and valve. It converts the rotating cam...
View full detailsNutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...
View full detailsRear Axle Case Bolt for the Salisbury rear axle. The bolt clamps the axle casing joint of the Salisbury (heavy-duty) rear axle, keeping the housin...
View full detailsValve Guide for the Rover V8 cylinder head. Pressed into the cylinder head, the guide supports the valve stem and keeps the valve concentric with ...
View full detailsBolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...
View full detailsChoke Cable for the carburettor cold-start system. The cable links the dash-mounted choke control to the carburettor, operating the choke mechanis...
View full detailsChoke Cable is the manual choke control cable in the carburettor fuel system, running from the dashboard choke knob to the carburettor choke lever....
View full detailsHeater Hose - Series 3 RHD
Primary Pinion Shim - 2.00 mm for the four-speed V8 gearbox. Used during gearbox assembly or rebuild to set the correct end-float and bearing prel...
View full detailsPrimary Pinion Bearing Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox casing. 2.05 mm thick, it control...
View full detailsInner Ring
Hose
Ignition Switch for the steering-column lock, diesel specification. The switch is the electrical unit that fits into the steering-column lock barre...
View full detailsRear Halfshaft for the Salisbury rear axle, 24-spline, right-hand side. The halfshaft transmits drive from the differential through the axle casin...
View full detailsSpring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...
View full detailsBrake Pedal Pivot Bush for the brake pedal assembly. It seats in the pedal box and forms the bearing surface on which the brake pedal pivots on it...
View full detailsRadiator Overflow Bottle fitted to the cooling system on Series II, Series III, and 101 Forward Control Land Rovers. This plastic reservoir collec...
View full detailsIntermediate Exhaust Pipe for the 2.6L 6-cylinder petrol engine. This is the centre section of the exhaust system, connecting the front pipe to th...
View full detailsSpring Shackle Distance Tube for the rear leaf spring shackle assembly. This spacer tube sets the correct spacing between the shackle plates, maint...
View full detailsTappet Adjuster is the adjustment screw used to set valve clearance in the cylinder head of Land Rover Series 4-cylinder engines. The screw thread...
View full detailsTappet Screw - the valve-clearance adjusting screw in the rocker gear of the four-cylinder engine (3-bearing crankshaft), part of the valvetrain. ...
View full detailsDistance Piece - a machined spacer in the axle and suspension assembly, specified for the 1-Ton Military configuration. It sets the standoff betwe...
View full detailsBrake & Clutch Reservoir Tank Kit, a replacement for the original single fluid reservoir that fed both the brake and clutch master cylinders. ...
View full detailsHandbrake Catch Pawl, the ratchet claw of the transmission parking brake mechanism. It engages the toothed quadrant on the handbrake lever, lockin...
View full detailsDifferential Bearing for the Rover-type axle, part of the differential carrier assembly inside the axle case. It supports the differential carrier...
View full detailsUpper Rear Door Seal, the rubber weatherseal for the top edge of the rear door aperture. It seals the upper line of the rear door against the body...
View full detailsFront Door Check Strap, part of the front door hinge and retention hardware. Connecting the front door to the body pillar, the check strap limits ...
View full detailsSill Panel Rear 109 Not Station Wagon - LH
Rear Sill Panel for the right-hand side of the body understructure on long wheelbase (109 inch) models. Fitted at the rear sill position, this pane...
View full detailsHeater Air Intake Trim fits the front wing air intake of the heating and ventilation system. It finishes the fresh-air intake aperture in the wing...
View full detailsEdge Clip - Door Lock Mechanism with various applications across Land Rover Series, Defender, Discovery 1, and Range Rover Classic models. This sp...
View full detailsDoor lock RH
Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...
View full detailsCheck rod RH
Fitment: all models to 1980
Inner Seat Base is the centre front seat base cushion, forming the lower seating platform of the basic vinyl front seat. Finished in black vinyl f...
View full detailsRope Hook - a securing hook for the canvas hood (soft top). It provides an anchor point around which the hood tie-down rope is passed, holding the...
View full detailsWasher
Hinge Pin - the pivot pin for the top hatch (windscreen) hinge. It passes through the hinge knuckles to retain the two halves of the hinge while a...
View full detailsIntermediate Shaft
Rocker Bracket Locating Dowel for the cylinder head and rocker assembly in the 2.25L and 2.5L petrol and diesel engines. This dowel locates the ro...
View full detailsParts for the classic Land Rover Defender 90, 110 and 130, covering L315 and L316 models built from 1983 to 2016. This collection does not include the Defender L663. Over 5,900 parts available across Genuine, OEM, and aftermarket quality tiers, for 200Tdi, 300Tdi, TD5, and Puma engine families.
This collection covers the classic Land Rover Defender produced from 1983 to 2016, in three body lengths: the 90 (short wheelbase), the 110 (long wheelbase), and the 130 (crew cab and high-capacity load variants). These span two platform designations. L315 refers to the earlier platform in use from 1983. L316 refers to the revised platform introduced in the early 1990s and used through to final production in January 2016.
This collection does not cover the current-generation Defender L663, introduced in 2020. Parts for the L663 are held separately under Land Rover Defender parts.
Engine FamiliesFour diesel engine families account for the majority of classic Defender rebuilds and restorations supported by this collection.
The 200Tdi was introduced in 1990 and produced through to 1994. It is a direct-injection turbodiesel known for mechanical simplicity. Common service and rebuild requirements include the head gasket, water pump, injector seals, and thermostat.
The 300Tdi ran from 1994 to 1998. It uses a belt-driven timing system and a revised cylinder head. Timing belt and water pump replacement is the highest-priority service interval on this engine. Complete timing kit assemblies for the 300Tdi are stocked.
The TD5 ran from 1998 to 2007 and was Land Rover's first electronically managed Defender engine. It introduced an integrated injector harness routed through the rocker cover, a revised fuel delivery system, and full ECU control. Commonly replaced components include the rocker cover gasket, injector harness, and exhaust manifold.
The Puma TDCi variants ran from 2007 to 2016. A 2.4 litre unit was used from 2007 to 2011, replaced by a 2.2 litre unit from 2011 onwards. Common service requirements include EGR components, cooling system parts, and turbo-related items.
Defenders built before 1990 and fitted with earlier units including the 2.25 petrol, 2.5 normally-aspirated diesel, or V8 petrol are also supported where parts cross-reference with the L315 platform. Use the engine filter or search by OEM part number for these variants.
Engine family production date ranges per Land Rover workshop manual specifications and the Land Rover parts catalogue for L315 and L316 platforms.
Some components differ between the 90, 110, and 130. Propshafts, chassis outriggers, fuel tanks, body tub sections, and wheelbase-specific brackets are body-length dependent. Where a part is specific to one or two body lengths, the product listing states this.
Components that fit across all three body lengths include most engine parts, brake components, axle rebuild kits, and electrical items. No body-length filter is needed for those categories.
Quality TiersParts in this collection are available in three quality tiers, each suited to different rebuild priorities and budgets.
Genuine Land Rover parts are original components produced by or for Land Rover to factory specification. These are the correct choice where an exact factory-spec replacement is required.
OEM-equivalent parts are produced by the original component manufacturer, often the same supplier that produced the part for Land Rover during original production. These offer factory-level quality at a lower price point than branded genuine parts and are widely used in professional workshop settings.
Aftermarket parts are third-party manufactured alternatives. Quality varies by supplier and application. For high-wear consumable items these are frequently a practical and cost-effective choice.
Use the quality filter on the left to narrow results by tier.
VIN LookupThe 17-character VIN on your Defender's identification plate encodes the body variant, engine family, and model year. For any part where fitment is uncertain, the VIN is the most reliable starting point for confirmation.
Budget Parts supports VIN-based fitment enquiries via the contact page. If you are unsure whether a part is correct for your specific Defender, use the part number search or submit an enquiry before ordering.
Related CategoriesSearching for a specific part type rather than browsing the full catalogue? The following collections group classic Defender components by category:
Propshafts, universal joints, and drivetrain rebuild components.
Land Rover driveshaft parts →The most reliable method is the VIN plate, usually found on the driver's side A-post or on a plate inside the door aperture. The engine code within the VIN confirms the engine family. As a general guide based on production dates: the 200Tdi was fitted from 1990 to 1994, the 300Tdi from 1994 to 1998, the TD5 from 1998 to 2007, and the Puma TDCi from 2007 to 2016. Defenders built before 1990 used earlier petrol and diesel units. The engine stamp on the block itself also confirms the variant if the VIN plate is absent or damaged.
No. Classic Defenders use era-specific loom designs that are not interchangeable between engine generations. The TD5 uses a loom that integrates with the ECU and routes the injector harness through the rocker cover, which is incompatible with earlier Tdi wiring architecture. Puma TDCi looms differ again due to the revised engine management system. Always match the loom to both the engine family and body length (90, 110, or 130) when ordering.
Wheelbase-specific components include propshafts, fuel tanks, chassis outriggers, body tub sections, and some bracket assemblies. Most mechanical components are shared across all three body lengths, including engine internals, brake components, axle rebuild parts, and the majority of electrical items. Product listings on this page state body-length fitment where it is relevant.
Some parts do cross-reference between the classic Defender and the Discovery 1, particularly for the 200Tdi engine, which shares components with the Discovery 1 200Tdi unit. Axle components also overlap to a degree between the two platforms. Cross-referencing by part number is essential before ordering, as not all apparently similar parts are dimensionally or functionally interchangeable. Use the part number search or contact Budget Parts with your VIN if you are unsure.
Genuine parts are Land Rover-branded components produced to original factory specification. OEM-equivalent parts are made by the original component supplier, often the same manufacturer that supplied Land Rover during production, and offer comparable quality without the Land Rover brand premium. Aftermarket parts are third-party alternatives that vary in quality by supplier. All three tiers are available in this collection and can be filtered using the quality selector.
The final classic Defender left the Solihull production line in January 2016, marking the end of a model that had been in continuous production since 1983. The current-generation Defender L663 is a separate vehicle on a different platform and is not covered by this collection.
The following guides cover engine-specific maintenance and component topics relevant to the Defender models in this collection. Each article provides detailed technical context and links back to the relevant parts.
A technical reference covering the 300Tdi engine's known weak points, service priorities, and the components most commonly required for a full rebuild or preventive overhaul.
Defender 300Tdi guide →Covers the TD5 exhaust manifold cracking failure in detail, including inspection method, replacement options, and why stud quality matters for a lasting repair.
Td5 exhaust manifold guide →A maintenance and fault reference for the Puma 2.4 TDCi engine fitted to post-2007 Defenders, covering EGR, cooling, and turbo-related service requirements.
Defender 2.4 TDCi guide →